G053
User´s Guide
Tungaloy
User ’s
Gu ide-
Techn i ca l Reference
¡
Increase the cutting speed by 10 % within standard conditions.
¡
Lower the feed by 10 %.
¡
Increase the cutting speed by 10 % within standard conditions.
¡
When the feed is extremely low or high, set up it within standard conditions.
¡
Confirm that the cutting fluid flow is higher than 7 liter/min.
¡
The concentration of cutting fluid must be higher than 5 %.
¡
Use the cutting fluid superior in lubricity.
¡
Change to internal cutting fluid supply from external one.
¡
Change to the machine with higher torque.
¡
Change to the clamp method with rigidity.
¡
Change the drill setting method.
¡
Change the grade to high wear resistant.
¡
Tighten the screw.
¡
Change to internal cutting fluid supply from external one.
¡
Increase the supply rate of the cutting fluid. (Higher than 10 liter/min.)
¡
Lower the feed by 20 % within standard conditions.
¡
Lower the cutting speed by 20 % within standard conditions.
¡
Lower the feed by 20 % within standard conditions.
¡
Lower the cutting speed by 20 % within standard conditions.
¡
Increase the cutting speed by 20% and lower the feed by 20% within standard conditions.
¡
Raise the fluid pressure (for higher than 1.5 MPa).
¡
Set the misalignment to 0 ~ 0.2 mm.
¡
Check the manual and use the tool in the allowable offset range.
¡
Flatten the entry surface in pre-machining.
¡
Set the feed for lower than 0.05 mm/rev in rough surface area.
¡
Lower the feed by 20 ~ 50 % within standard conditions.
¡
Confirm the corner when exchanging inserts.
¡
Exchange the corner or the insert before the nose wear
reaches 0.3 mm.
¡
Flatten the entry surface in pre-machining.
¡
Set the feed for lower than 0.05 mm/rev at rough surface area.
¡
Set the feed for lower than 0.05 mm/rev in interrupted area.
¡
Confirm the corner when exchanging inserts.
¡
Increase the cutting speed by 20 % and lower the feed by 20 % within standard conditions.
¡
Raise the fluid pressure (for higher than 1.5 MPa).
¡
Lower the feed by 20 % within standard conditions.
¡
Change to continuous feed in case of pick feeding.
¡
Exchange the corner or the insert before the nose wear
reaches 0.3 mm.
¡
Change to the machine with higher rigidity.
¡
Change to the clamp method with rigidity.
¡
Change the drill setting method.
¡
Set the feed for lower than 0.05 mm/rev.
¡
Change to internal cutting fluid supply from external one.
¡
Lower the feed by 20 % within standard conditions.
¡
Change the grade to toughress.
¡
Tighten the screw.
Inappropriate cutting conditions
Inappropriate cutting conditions
Varieties and supply of cutting fluid
Vibration in drilling
Unsuitable for selection of grade
Looseness of screws
Cutting heat is too high
Excessive chip welding
Chip packing
Misalignment for workpiece rotation
Large offset
No flatness of machined surface
High feed
Using a chipping corner
Using inserts in excess of tool-life
No flatness of machined surface
The existence of interrupted area
Using a chipped corner
High hardness of workpiece
Chip packing
Machinery impact
Using inserts in excess of tool-life
Vibration in drilling
High hardness of workpiece
Thermal impact
Unsuitable for selection of grade
Looseness of screws
Relief surface
Relief surface
Relief surface
Crater
Chipbreaker
The rotation
center of drill
Peripheral
corner area
The unused
corner area
and cutting
edge
Contact
boundary
Flaking
Common
Central
cutting
edge
Peripheral
cutting
edge
Common
Central
cutting
edge
Peripheral
cutting
edge
Common
Abnormal wear
Chipping and fracture
Problem
Cause
Countermeasure
Troubleshoot ing for indexabl e dr i l l s
Dr i l l ing Tool s