G054
User´s Guide
User ’s
Gu ide-
Techn i ca l Reference
Problem
Cause
Countermeasure
¡
Set the misalignment to 0 ~ 0.2 mm.
¡
Use the tool in the allowable offset range.
¡
Set offset direction extended diameter of workpiece
¡
Flatten the entry surface in pre-machining.
¡
Set the feed for lower than 0.05 mm/rev in rough surface area.
¡
Exchange the insert.
¡
Change to the clamp method with rigidity.
¡
Increase the cutting speed by 20 % and lower the feed by 20 % within standard conditions.
¡
Raise the fluid pressure (for higher than 1.5 MPa).
¡
Set the misalignment to 0 ~ 0.2 mm.
¡
Adjust offset contents.
¡
Flatten the entry surface in pre-machining.
¡
Set the feed for lower than 0.05 mm/rev at rough surface area.
¡
Change to the clamp method with rigidity.
¡
The concentration of cutting fluid must be higher than 5 %.
¡
Use the cutting fluid superior in lubricity.
¡
Change to internal cutting fluid supply from external one.
¡
Increase the cutting speed by 20 % within standard conditions.
¡
Lower the feed by 20 % within standard conditions.
¡
Exchange the insert.
¡
Increase the cutting speed by 20 % and lower the feed by 20 % within standard conditions.
¡
Raise the fluid pressure (for higher than 1.5 MPa).
¡
Tighten the screw.
¡
Work within standard conditions.
¡
Increase the cutting speed by 10 % within standard conditions.
¡
Increase the feed by 10 % within standard conditions.
¡
Exchange inserts.
¡
Change to internal cutting fluid supply from external one.
¡
Work by step feed.
¡
Use dwell function for 0.1 sec approximately.
¡
There is a tendency to shorten the chips when shifting to higher
speed and feed.
¡
Change to internal cutting fluid supply from external one.
¡
Raise the fluid pressure (for higher than 1.5 MPa).
¡
Increase the cutting speed by 20 % and lower the feed by 20 % within standard conditions.
¡
Raise the fluid pressure (for higher than 1.5 MPa).
¡
Exchange the drill holder.
¡
Tighten the screw.
¡
Lower the cutting speed by 20 % within standard conditions.
¡
Increase the feed by 10 % within standard conditions.
¡
Exchange the insert.
¡
Change to the machine with higher torque rigidity.
¡
Change to the clamp method with rigidity.
¡
Change the drill setting method.
¡
Tighten the screw.
¡
Use the range of number of revolutions suited machine spec. Lower the feed by 20 ~ 50%.
¡
Exchange inserts before the failure becomes larger.
¡
Check the oil-hole plug screw is tightly screwed in place.
¡
Check that the fluid flows powerfully from the drill.
¡
Lower the cutting speed and the feed by 20 % within
standard conditions.
¡
Exchange the insert.
¡
Lower the feed by 20 ~ 50% just before leaving from the workpiece.
Misalignment of workpiece rotation
Offset machining in excess of allowable range
Offset direction reduced diameter of workpiece
No flatness of the entry surface
Chipping of peripheral cutting edge
Bend of workpiece
Chip packing
Misalignment for workpiece rotation
Inappropriate offset contents
No flatness of the entry surface
Bend of workpiece
Varieties and supply of cutting fluid
Inappropriate cutting conditions
Failures of inserts
Chip packing
Looseness of screws
Inappropriate cutting conditions
Failures of inserts
Machining by external fluid supply
Chips around the central cutting edge
Fluid supply
Inappropriate cutting conditions
Large failure of drill holders
Looseness of screws
Inappropriate cutting conditionss
Large wear of inserts
Vibration in drilling
Looseness of screws
Insufficient machine power and torque
Burned inserts
Failures of inserts
Inappropriate cutting conditions
The tool periphery
Hole diameter
Roughness
Common
Prolonged and
twisted of chips
Chip packing
Common
Chatter
Machine stop
Large burr
Scratch marks on the tool
Inappropriate hole accuracy
Chip control
Others
Dr i l l ing Tool s