Unknown - page 993

E043
Tungaloy
2-e ective Drill
Designation
øD
c
AH180 øD
s
ℓ
ℓ
s
L
DSX1560F08
15.6
16
176
66
242
DSX1570F08
15.7
16
176
66
242
DSX1580F08
15.8
16
176
66
242
DSX1590F08
15.9
16
176
66
242
DSX1600F08
16
●
16
176
66
242
STANDARD CUTTING CONDITIONS
ISO Workpiece
material
Examples
JIS (ISO)
Hardness
Cutting speed:
Vc
(m/min)
Feed: f (mm/rev)
ø3 ~ ø6 ø6 ~ ø10 ø10 ~ ø20 ø3 ~ ø6 ø6 ~ ø10 ø10 ~ ø20
Mild steels,
Low carbon steels
C15E4, E275A < 180HB 70 - 140
80 - 160
90 - 190 0.15 - 0.25 0.2 - 0.35 0.25 - 0.4
Carbon steels,
Alloy steels
C45, 42CrMo4 180 ~ 300HB 50 - 130
70 - 160
80 - 170 0.15 - 0.25 0.2 - 0.35 0.25 - 0.4
High alloy steels etc.
42CrMoS4 250 ~ 350HB 40 - 100
60 - 140
60 - 160
0.1 - 0.2
0.15 - 0.3 0.15 - 0.3
Stainless steels
X5CrNi18-9
< 200HB
30 - 70
50 - 100
50 - 120
0.1 - 0.2
0.1 - 0.25 0.15 - 0.35
Grey cast irons
250
< 200HB 80 - 140
100 - 160 100 - 180 0.15 - 0.35 0.2 - 0.4
0.25 - 0.5
Ductile cast irons
450-10S
< 300HB 70 - 140
80 - 150
80 - 170 0.15 - 0.35 0.2 - 0.4 0.25 - 0.45
Aluminium alloys
AlSi11Cu3
-
80 - 160
100 - 180 100 - 190 0.15 - 0.35 0.2 - 0.45 0.25 - 0.6
Titanium alloys
Ti-6Al-4V
-
25 - 60
30
- 80
30 - 80
0.1 - 0.2
0.1 - 0.25 0.15 - 0.35
Heat-resistant alloys
Inconel
250HB <
10 - 30
10 - 40
10 - 40
0.02 - 0.1 0.05 - 0.15 0.1 - 0.25
High hardened steels X153CrMoV12
< 40HRC 20 - 50
30 - 60
30 - 60
0.08 - 0.1 0.1 - 0.15 0.12 - 0.2
: Line-up
Note: • The cutting parameters shown in the table are merely a starting
guideline for general machining.
• Values should be varied depending on the power or rigidity of the
machine to be used. For the smaller side of drill diameters, select
lower feeds.
• Chip packing in the oil holes may cause drill breakage. A filter pre-
venting the circulation of chips should be used on coolant supply.
• Inconel is trademark of Huntington Alloys, Inc.
• No. of revolutions (min
-1
) = Cutting speed 1000 ÷ 3.14 ÷ Tool diameter
• Table feed (mm/min) = No. of revolutions Feed per revolution
1...,983,984,985,986,987,988,989,990,991,992 994,995,996,997,998,999,1000,1001,1002,1003,...1348
Powered by FlippingBook