E047
Tungaloy
2-e ective Drill
Designation
øD
c
AH180 øD
s
ℓ
ℓ
s
L
DSE1560F03
15.6
15.6
96
64
160
DSE1570F03
15.7
15.7
96
64
160
DSE1580F03
15.8
15.8
96
64
160
DSE1590F03
15.9
15.9
96
64
160
DSE1600F03
16
●
16
96
64
160
ISO
Workpiece
material
Examples Hardness
Cutting speed: Vc (m/min)
Feed: f (mm/rev)
ø3 ~ ø6 ø6 ~ ø10 ø10 ~ ø20 ø3 ~ ø6 ø5 ~ ø10 ø10 ~ ø20
Mild steels,
Low carbon steels
E275A < 180HB
40 - 100
60 - 120
60 - 130
0.15 - 0.3
0.15 - 0.35
0.2 - 0.5
Carbon steels,
Alloy steels
C45 180 ~ 300HB 40 - 90
50 - 120
60 - 130
0.15 - 0.3
0.15 - 0.35
0.15 - 0.4
High alloy steels etc.
42CrMo4 250 ~ 350HB 40 - 80
50 - 100
50 - 100
0.1 - 0.2
0.15 - 0.25 0.15 - 0.35
Stainless steels X5CrNi18-9 < 200HB
10 - 20
10 - 20
10 - 20
0.05 - 0.15 0.05 - 0.15 0.05 - 0.15
Grey cast irons
300
< 200HB
40 - 90
50 - 95
50 - 100
0.15 - 0.3
0.2 - 0.4
0.2 - 0.4
Ductile cast irons
600-3
< 300HB
35 - 80
40 - 85
45 - 90
0.15 - 0.3
0.2 - 0.4
0.2 - 0.4
Titanium alloys
Ti-6Al-4V
20 - 40
20 - 40
20 - 40
0.1 - 0.2
0.15 - 0.25
0.15 - 0.4
Heat-resistant alloys Inconel718 250HB <
10 - 30
10 - 30
10 - 30
0.03 - 0.07 0.05 - 0.1
0.07 - 0.12
High hardened steels X153CrMoV12 < 40HRC 20 - 40
20 - 40
20 - 40
0.05 - 0.15 0.05 - 0.15 0.07 - 0.2
STANDARD CUTTING CONDITIONS
: Line-up
Notes:
• Because the cutting conditions may be changed depending on the mate-
rial type, hardness, machinability, machine tool, and coolant, the most
appropriate conditions must be decided whilst referring the chip control
condition and tool failure mode.
• When using the smaller side of the diameter range, the feed rate should be
set lower.
• When drilling difficult-to-cut materials, coolant supplying conditions are
critical for successful drilling. So, the use of constant and flood coolant is
highly recommended.
• For the standard DSE-type drills, somewhat large honing width intended
for drilling of general steels is applied. But, when drilling difficult-to-cut
materials having high hardness, requiring lowering the feed rate, the hon-
ing width should be modified.
• The drills with special honing specification are made to order on request.
• Inconel is trademark of Huntington Alloys, Inc.