Unknown - page 1005

E055
Tungaloy
2-e ective Drill
ISO
Workpiece
material
Examples
(JIS)
Hardness Cutting speed
Vc (m/min)
Feed: f (mm/rev)
ø3 ~ ø5
ø5 ~ ø10
ø10 ~ ø16
ø16 ~ ø20
Mild steels·
Low Carbon steels E275A < 180HB
40 - 80
0.15 - 0.25
0.15 - 0.3
0.2 - 0.4
0.25 - 0.5
Carbon steels ·
Alloy steels
C55 180 ~ 300HB
40 - 80
0.15 - 0.25
0.15 - 0.3
0.2 - 0.4
0.25 - 0.5
High alloy steets etc. 42CrMo4 250 ~ 350HB
40 - 70
0.1 - 0.2
0.15 - 0.25
0.15 - 0.3
0.2 - 0.4
Stainless steels X5CrNi18-9 < 200HB
20 - 40
0.05 - 0.2
0.1 - 0.25
0.1 - 0.3
0.15 - 0.3
Grey cast irons
300
< 300HB
40 - 80
0.15 - 0.35
0.25 - 0.45
0.3 - 0.6
0.35 - 0.65
Ductile cast irons
600-3
< 300HB
40 - 80
0.15 - 0.3
0.2 - 0.4
0.25 - 0.5
0.3 - 0.6
Titanium alloys
Ti-6Al-4V
20 - 40
0.1- 0.2
0.15 - 0.25
0.15 - 0.3
0.2 - 0.4
Heat-resistant alloys Inconel
250HB <
10 - 30
0.03 - 0.07
0.05 - 0.1
0.07 - 0.12
0.07 - 0.12
High hardened steels X153CrMoV12 < 45HRC
10 - 30
0.03 - 0.07
0.05 - 0.1
0.07 - 0.12
0.07 - 0.12
• Cutting fluid should be sufficiently supplied to the drill point and the entrance of the hole.
• Use a water-soluble cutting fluid.
Designation
øD
c
AH170 øD
s
ℓ
ℓ
s
L
DMX156M
15.6
●
15.6 96 64 160
DMX157M
15.7
●
15.7 96 64 160
DMX158M
15.8
●
15.8 96 64 160
DMX159M
15.9
●
15.9 96 64 160
DMX160M
16
●
16 96 64 160
DMX165M
16.5
●
16.5 102 65 167
DMX170M
17
●
17 102 65 167
DMX175M
17.5
●
17.5 102 65 167
DMX180M
18
●
18 102 65 167
DMX185M
18.5
●
18.5 114 65 179
DMX190M
19
●
19 114 65 179
DMX195M
19.5
●
19.5 114 65 179
DMX200M
20
●
20 114 65 179
STANDARD CUTTING CONDITIONS
: Line-up
Note:
• Because the cutting conditions may be changed depending on the mate-
rial type, hardness, machinability, machine tool, and coolant, the most
appropriate conditions must be decided whilst referring the chip control
condition and tool failure mode.
• When using the smaller side of the diameter range, the feed rate should be
set lower.
• When drilling difficult-to-cut materials, coolant supplying conditions are
critical for successful drilling. So, the use of constant and flood coolant is
highly recommended.
• For the standard DMX-type drills, somewhat large honing width intended
for drilling of general steels is applied. But, when drilling difficult-to-cut
materials having high hardness, requiring lowering the feed rate, the hon-
ing width should be modified.
• The drills with special honing specification are made to order on request.
• Inconel is trademark of Huntington Alloys, Inc.
1...,995,996,997,998,999,1000,1001,1002,1003,1004 1006,1007,1008,1009,1010,1011,1012,1013,1014,1015,...1348
Powered by FlippingBook