D137
Tungaloy
Face Milling
Cutting
speed
vc (m/min)
Light cutting to finishing (Depth of cut: ≤ 1.0 mm)
ISO Workpiece material
Priority
Grade
Feed per tooth: fz (mm/t)
MJ
ML
HJ
MS
Flat
AJ
Mild and
low carbon steels
E275, etc.
< 180 HB
First choice
AH3135
AH120 100 - 270 0.05 - 0.25 0.05 - 0.2 0.2 - 0.6 0.1 - 0.2 0.05 - 0.25
-
Priority on wear
resistance
T3130 150 - 300 0.05 - 0.25
-
0.2 - 0.6
-
0.05 - 0.25
-
Priority on surface
quality
NS740 100 - 300 0.05 - 0.2
-
-
-
0.05 - 0.2
-
Carbon and
alloy steels
C45, 42CrMo4, etc.
< 300 HB
First choice
AH3135
AH120 100 - 230 0.05 - 0.2 0.05 - 0.15 0.2 - 0.5
-
0.05 - 0.2
-
Priority on wear
resistance
T3130 150 - 280 0.05 - 0.2
-
0.2 - 0.5
-
0.05 - 0.2
-
Priority on surface
quality
NS740 100 - 230 0.05 - 0.18
-
-
-
0.05 - 0.18
-
Die steels
X96CrMoV12, etc.
< 30 HRC
First choice
AH3135
AH120 100 - 180 0.05 - 0.18 0.05 - 0.12 0.2 - 0.4
-
0.05 - 0.18
-
Priority on wear
resistance
T3130 100 - 180 0.05 - 0.18
-
0.2 - 0.4
-
0.05 - 0.18
-
Stainless steels
X5CrNi18-9,
X5CrNiMo17-12-2, etc.
< 250 HB
First choice
AH3135
AH130 80 - 200 0.1 - 0.2
-
0.2 - 0.5 0.1 - 0.18
-
-
Priority on wear
resistance
AH120 150 - 250 0.1 - 0.2 0.1 - 0.18 0.2 - 0.5
-
0.1 - 0.2
-
Grey cast irons
250, 300, etc.
First choice
T1215 180 - 300 0.1 - 0.2
-
0.2 - 0.6
-
0.1 - 0.2
-
Priority on impact
resistance
AH120 150 - 250 0.1 - 0.2 0.05 - 0.18 0.2 - 0.6
-
0.1 - 0.2
-
Ductile cast irons
400-15S, 600-3, etc.
First choice
T1215 120 - 200 0.1 - 0.2
-
0.2 - 0.6
-
0.1 - 0.2
-
Priority on impact
resistance
AH120 100 - 180 0.1 - 0.2 0.05 - 0.18 0.2 - 0.6
-
0.1 - 0.2
-
Aluminium alloys
Si < 13 %
-
DS1100
KS05F 300 - 1000
-
-
-
-
-
0.05 - 0.2
Aluminium alloys
Si ≥ 13%
-
DS1100
KS05F 80 - 300
-
-
-
-
-
0.05 - 0.2
Copper alloys
-
DS1100
KS05F 200 - 500
-
-
-
-
-
0.05 - 0.2
Notes:
· When cutting at a large depth of cut or a large cutting width, the cutting
speed (vc) and feed (fz) should be set to the lower side of the values shown
in the above table.
· Dry cutting (or air-blowing) is generally recommended. However, when
chips tend to excessively adhere to the cutting edges when machining
stainless steel, use a water soluble cutting fluid. In this case, use the AH140
grade at speeds lower than vc = 100 m/min.
· When wet machining mild steels, carbon steels and alloy steels, use T3130
at lower cutting conditions.
· TAW13 type TAC mills cannot be used for axial-feed cutting such as
ramping, plunging and drilling.