D109
Tungaloy
Shoulder Milling
STANDARD CUTTING CONDITIONS
ISO Workpiece material
Grade
Roughing
(Depth of cut: ap > 1.5 mm)
Finishing
(Depth of cut: ap = 0.3 ~ 0.7 mm)
Cutting speed
Vc (m/min)
Feed per tooth
fz (mm/t)
Cutting speed
Vc (m/min)
Feed per tooth
fz (mm/t)
Mild steels
Unhardened steels
< 180 HB
GH330
100 ~ 230
0.1 ~ 0.25
130 ~ 250
0.1 ~ 0.3
T3130
130 ~ 300
0.1 ~ 0.28
180 ~ 300
0.1 ~ 0.3
UX30
100 ~ 180
0.1 ~ 0.25
130 ~ 200
0.1 ~ 0.3
Carbon steels
Alloy steels
< 300 HB
GH330
100 ~ 180
0.1 ~ 0.2
130 ~ 200
0.1 ~ 0.28
T3130
130 ~ 280
0.1 ~ 0.25
180 ~ 280
0.1 ~ 0.28
UX30
80 ~ 130
0.1 ~ 0.2
100 ~ 150
0.1 ~ 0.28
Die steels
< 30 HRC
GH330
100 ~ 150
0.1 ~ 0.18
100 ~ 150
0.1 ~ 0.2
UX30
80 ~ 130
0.1 ~ 0.18
80 ~ 130
0.1 ~ 0.2
Stainless steels
< 250 HB
GH330
150 ~ 200
0.15 ~ 0.23
200 ~ 250
0.15 ~ 0.25
Cast irons
Ductile cast irons
T1115
100 ~ 200
0.1 ~ 0.2
100 ~ 200
0.1 ~ 0.25
UX30
80 ~ 130
0.1 ~ 0.2
80 ~ 130
0.1 ~ 0.25
ISO Workpiece material
Grade
Roughing
(Depth of cut: ap > 1.5 mm)
Finishing
(Depth of cut: ap = 0.3 ~ 0.7 mm)
Cutting speed
Vc (m/min)
Feed per tooth
fz (mm/t)
Cutting speed
Vc (m/min)
Feed per tooth
fz (mm/t)
Mild steels
Unhardened steels
< 180 HB
GH330
130 ~ 230
0.05 ~ 0.17
150 ~ 250
0.05 ~ 0.2
AH330
130 ~ 370
0.05 ~ 0.17
150 ~ 400
0.05 ~ 0.2
Carbon steels
Alloy steels
< 300 HB
GH330
150 ~ 180
0.05 ~ 0.12
150 ~ 200
0.05 ~ 0.15
Stainless steels
< 250 HB
GH330
150 ~ 200
0.05 ~ 0.12
200 ~ 250
0.05 ~ 0.15
ISO Workpiece material
Grade
Roughing
(Depth of cut: ap > 1.5 mm)
Finishing
(Depth of cut: ap = 0.3 ~ 0.7 mm)
Cutting speed
Vc (m/min)
Feed per tooth
fz (mm/t)
Cutting speed
Vc (m/min)
Feed per tooth
fz (mm/t)
Mild steels
Unhardened steels
< 180 HB
GH330
100 ~ 230
0.15 ~ 0.3
130 ~ 250
0.15 ~ 0.35
T3130
130 ~ 300
0.15 ~ 0.33
180 ~ 300
0.15 ~ 0.38
UX30
100 ~ 180
0.15 ~ 0.3
130 ~ 200
0.15 ~ 0.35
Carbon steels
Alloy steels
< 300 HB
GH330
100 ~ 180
0.15 ~ 0.24
130 ~ 200
0.15 ~ 0.35
T3130
130 ~ 280
0.15 ~ 0.3
180 ~ 280
0.15 ~ 0.35
UX30
80 ~ 130
0.15 ~ 0.24
100 ~ 150
0.15 ~ 0.35
Die steels
< 30 HRC
GH330
100 ~ 150
0.15 ~ 0.22
100 ~ 150
0.15 ~ 0.28
UX30
80 ~ 130
0.15 ~ 0.22
80 ~ 130
0.15 ~ 0.28
Cast irons
Ductile cast irons
T1115
100 ~ 200
0.15 ~ 0.24
100 ~ 200
0.15 ~ 0.3
UX30
80 ~ 130
0.15 ~ 0.24
80 ~ 130
0.15 ~ 0.3
Notes:
• As a rule, dry cutting (or air-blowing) is generally recommended.
• If a cutting fluid is used, the cutting speed should be set to the lower side
of the values shown in the above table.
• When being used in square shoulder milling, climb milling is recommend-
ed.
• In square shoulder milling of stainless steel, when chips tend to be recut
during cutting, change to up-milling mode.
• When wet machining mild steels, carbon steels and alloy steels, use T3130
at lower cutting conditions.
For MJ-chipbreaker inser ts (Genera l purpose)
For ML-chipbreaker inser ts (Sharpness-pr ior i ty)
For MH-chipbreaker inser ts (Toughness-pr iori ty )