D115
Tungaloy
Shoulder Milling
STANDARD CUTTING CONDITIONS
ISO
Workpiece
material
Grade
Roughing (Depth of cut ap: > 1.5 mm) Finishing (Depth of cut ap: 0.3 ~ 0.7 mm)
Cutting speed Vc (m/min)
Feed per tooth fz (mm/t)
Cutting speed Vc (m/min)
Feed per tooth fz (mm/t)
Mild steels
Unhardened steels
< 180 HB
AH330
130 ~ 370
0.1 ~ 0.2
150 ~ 400
0.1 ~ 0.23
AH120 « GH330
130 ~ 230
0.1 ~ 0.2
150 ~ 250
0.1 ~ 0.23
T3130
130 ~ 300
0.1 ~ 0.23
180 ~ 300
0.1 ~ 0.25
NS740 « N308
130 ~ 200
0.1 ~ 0.18
150 ~ 250
0.1 ~ 0.2
UX30 « AH140
100 ~ 180
0.1 ~ 0.2
130 ~ 200
0.1 ~ 0.23
Carbon steels
Alloy steels
< 300 HB
AH330
100 ~ 300
0.1 ~ 0.18
150 ~ 320
0.1 ~ 0.2
AH120 « GH330
100 ~ 180
0.1 ~ 0.18
150 ~ 200
0.1 ~ 0.2
T3130
130 ~ 280
0.1 ~ 0.2
180 ~ 280
0.1 ~ 0.23
AH140
80 ~ 130
0.1 ~ 0.18
100 ~ 200
0.1 ~ 0.18
NS740 « N308
100 ~ 150
0.1 ~ 0.15
150 ~ 200
0.1 ~ 0.18
UX30
80 ~ 130
0.1 ~ 0.18
100 ~ 150
0.1 ~ 0.2
Die steels
< 30 HRC
AH330
100 ~ 250
0.1 ~ 0.15
100 ~ 250
0.1 ~ 0.2
T3130 « AH120 « GH330
100 ~ 150
0.1 ~ 0.15
100 ~ 150
0.1 ~ 0.2
UX30
80 ~ 130
0.1 ~ 0.15
80 ~ 130
0.1 ~ 0.2
Stainless steels
< 250 HB
AH130 « AH140
80 ~ 180
0.1 ~ 0.2
100 ~ 200
0.1 ~ 0.25
AH120
150 ~ 200
0.1 ~ 0.18
200 ~ 250
0.1 ~ 0.25
Cast irons
Ductile cast irons
T1115
100 ~ 200
0.1 ~ 0.2
100 ~ 200
0.1 ~ 0.25
TH10
80 ~ 130
0.1 ~ 0.2
80 ~ 130
0.1 ~ 0.25
Aluminium alloys
Si < 13%
TH10
200 ~ 1000
0.05 ~ 0.25
350 ~ 1000
0.1 ~ 0.25
DX140
200 ~ 1000
0.05 ~ 0.15
350 ~ 1000
0.1 ~ 0.2
Copper alloys
TH10
200 ~ 500
0.1 ~ 0.15
200 ~ 500
0.1 ~ 0.2
Note:
• Dry cutting is recommended for all materials except for aluminium alloys.
• Maximum depth of cut for TECN43ZFR-DIA is 3.5 mm.
• When wet machining mild steels, carbon steels and alloy steels, use T3130 at lower cutting conditions.
• No. of revolutions (min
-1
) = Cutting speed 1000 ÷ 3.14 ÷ Cutter diameter
• Table feed (mm/min) = No. of revolutions Feed per tooth No. of inserts