Unknown - page 603

D011
Tungaloy
High-Feed Milling
ø22
ø25
ø28
ø30
ø32
ø35
ø40
ø50
n
Vf
n
Vf
n
Vf
n
Vf
n
Vf
n
Vf
n
Vf
n
Vf
z = 3 z = 4
z = 4 z = 5
z = 4 z = 5
z = 4 z = 5
z = 5 z = 6
z = 5 z = 6
z = 5 z = 6
z = 5 z = 8
2,890 6,940 9,250 2,550 10,200 12,750 2,270 9,080 11,350 2,120 8,480 10,600 1,990 9,950 11,940 1,820 9,100 10,920 1,590 7,950 9,540 1,270 6,350 10,160
Vc = 200 m/min, fz = 1 mm/t
2,890 5,200 6,940 2,550 8,160 10,200 2,270 7,260 9,080 2,120 6,780 8,480 1,990 7,960 9,550 1,820 7,280 8,740 1,590 6,360 7,630 1,270 5,080 8,130
Vc = 200 m/min, fz = 0.8 mm/t
2,890 6,940 9,250 2,550 10,200 12,750 2,270 9,080 11,350 2,120 8,480 10,600 1,990 9,950 11,940 1,820 9,100 10,920 1,590 7,950 9,540 1,270 6,350 10,160
Vc = 200 m/min, fz = 1 mm/t
2,170 5,210 6,940 1,910 7,640 9,550 1,710 6,840 8,550 1,590 6,360 7,950 1,490 7,450 8,940 1,360 6,800 8,160 1,190 5,950 7,140 950 4,750 5,700
Vc = 150 m/min, fz = 1 mm/t
2,170 3,910 5,210 1,910 6,110 7,640 1,710 5,470 6,840 1,590 5,090 6,360 1,490 5,960 7,150 1,360 5,440 6,530 1,190 4,760 5,710 950 3,800 4,560
Vc = 150 m/min, fz = 0.8 mm/t
2,170 5,210 6,940 1,910 7,640 9,550 1,710 6,840 8,550 1,590 6,360 7,950 1,490 7,450 8,940 1,360 6,800 8,160 1,190 5,950 7,140 950 4,750 5,700
Vc = 150 m/min, fz = 1 mm/t
2,170 3,910 5,210 1,910 6,110 7,640 1,710 5,470 6,840 1,590 5,090 6,360 1,490 5,960 7,150 1,360 5,440 6,530 1,190 4,760 5,710 950 3,800 4,560
Vc = 150 m/min, fz = 0.8 mm/t
1,740 2,090 2,780 1,530 3,060 3,830 1,360 2,720 3,400 1,270 2,540 3,180 1,190 2,980 3,570 1,090 2,730 3,270 950 2,380 2,850 760 1,900 3,040
Vc = 120 m/min, fz = 0.5 mm/t
1,740 2,610 3,480 1,530 3,670 4,590 1,360 3,264 4,080 1,270 3,050 3,810 1,190 3,570 4,280 1,090 3,270 3,920 950 2,850 3,420 760 2,280 3,650
Vc = 120 m/min, fz = 0.6 mm/t
2,890 6,940 9,250 2,550 10,200 12,750 2,270 9,080 11,350 2,120 8,480 10,600 1,990 9,950 11,940 1,820 9,100 10,920 1,590 7,950 9,540 1,270 6,350 10,160
Vc = 200 m/min, fz = 1 mm/t
2,890 5,200 6,940 2,550 8,160 10,200 2,270 7,260 9,080 2,120 6,780 8,480 1,990 7,960 9,550 1,820 7,280 8,740 1,590 6,360 7,630 1,270 5,080 8,130
Vc = 200 m/min, fz = 0.8 mm/t
2,170 5,210 6,940 1,910 7,640 9,550 1,710 6,840 8,550 1,590 6,360 7,950 1,490 7,450 8,940 1,360 6,800 8,160 1,190 5,950 7,140 950 4,750 5,700
Vc = 150 m/min, fz = 1 mm/t
2,170 3,910 5,210 1,910 6,110 7,640 1,710 5,470 6,840 1,590 5,090 6,360 1,490 5,960 7,150 1,360 5,440 6,530 1,190 4,760 5,710 950 3,800 4,560
Vc = 150 m/min, fz = 0.8 mm/t
580 700 930 510 1,020 1,280 450 900 1,130 420 840 1,050 400 1,000 1,200 360 900 1,080 320 800 960 250 630 1,000
Vc = 40 m/min, fz = 0.5 mm/t
430 190 260 380 300 290 340 270 260 320 260 240 300 300 270 270 270 240 240 240 220 190 190 230
Vc = 30 m/min, fz = 0.2 mm/t
1,450 650 870 1,270 1,020 1,270 1,140 910 1,140 1,060 850 1,060 990 990 1,190 910 910 1,090 800 800 960 640 640 1,020
Vc = 100 m/min, fz = 0.2 mm/t
870 100 140 760 150 190 680 140 170 640 130 160 600 150 180 550 140 170 480 120 140 380 100 150
Vc = 60 m/min, fz = 0.05 mm/t
The above table shows the conditions for standard shank type cutters.
When using long shank type cutters, the number of teeth may be diŸerent.
In this case, the cutting conditions should be changed by referring to: “The
usage of standard and long shanks” shown in previous page.
Cutting conditions are generally limited by the rigidity and power of the
machine and the rigidity of the workpiece. When setting the conditions, start
from half of the values of the standard cutting conditions and then increase
the value gradually while making sure the machine is running normally.
Tool dia.
Max. depth
of cut
Max. ramping
angle
Max. plunging
depth
Max. cutting width
in plunging
Min.machinable
hole dia.
Max.machinable
hole dia.
Max. cutting width
in enlarged hole
Designation
øD
c
Max ap
θ°
A
W
øD1
øD2
ae
E/HXN03R016M...
ø16
1
2.1
0.3
3.5
22
30
12.5
E/HXN03R018M...
ø18
1
1.7
0.3
3.5
26
34
14.5
E/HXN03R020M...
ø20
1
1.4
0.3
3.5
30
38
16.5
E/HXN03R022M...
ø22
1
1.2
0.3
3.5
34
42
18.5
E/HXN03R025M...
ø25
1
1.0
0.3
3.5
40
48
21.5
E/HXN03R028M...
ø28
1
0.8
0.3
3.5
46
54
24.5
E/HXN03R030M...
ø30
1
0.7
0.3
3.5
50
58
26.5
E/HXN03R032M...
ø32
1
0.7
0.3
3.5
54
62
28.5
EXN03R035M...
ø35
1
0.6
0.3
3.5
60
68
31.5
TXN03R040M...
ø40
1
0.5
0.3
3.5
70
78
36.5
TXN03R050M...
ø50
1
0.4
0.3
3.5
90
98
46.5
· For øDc above 33 mm, slot milling, ramping or contouring is not recommended as chips may be re-cut.
ø
D
1, ø
D
2
θ
a
p
A
W
a
e
a
p
Shoulder
milling
Slotting
Traversing
Small depth
plunging
Ramping
Plunging
Drilling
(Helical feed)
Enlarged hole
APPLICATION RANGE
Tool dia.: øDc (mm), Number of revolutions: n (min
-1
), Feed speed: Vf (mm/min), Max. depth of cut: ap = 1.0 mm
1...,593,594,595,596,597,598,599,600,601,602 604,605,606,607,608,609,610,611,612,613,...1348
Powered by FlippingBook