Unknown - page 602

D010
High-Feed Milling
ISO
ø16, z = 2 ø18, z = 2
ø20
Vc
(m/min) ø16 ~ ø22 ø25 ~ ø50
n Vf
n Vf
n
Vf
z = 3 z = 4
Carbon steel
C45, C55, etc.
~ 300HB
First choice
AH725 MJ 100 - 300 0.5 - 1.2 0.5 - 1.5 0.1
3,980 6,370 3,540 5,660 3,180 7,630 10,180
Vc = 200 m/min, fz = 0.8 mm/t
~ 300HB
For low
cutting force
AH725 ML 100 - 300 0.5 - 0.7 0.5 - 1 0.1
3,980 4,780 3,540 4,250 3,180 5,720 7,630
Vc = 200 m/min, fz = 0.6 mm/t
~ 300HB
For impact
resistance
AH3035 MJ 100 - 300 0.5 - 1.2 0.5 - 1.5 0.1
3,980 6,370 3,540 5,660 3,180 7,630 10,180
Vc = 200 m/min, fz = 0.8 mm/t
Alloy steel
42CrMo4, 17Cr3, etc.
~ 300HB
First choice
AH725 MJ 100 - 200 0.5 - 1.2 0.5 - 1.5 0.1
2,980 4,770 2,650 4,240 2,390 5,740 7,650
Vc = 150 m/min, fz = 0.8 mm/t
~ 300HB
For low
cutting force
AH725 ML 100 - 200 0.5 - 0.7 0.5 - 1 0.1
2,980 3,580 2,650 3,180 2,390 4,300 5,740
Vc = 150 m/min, fz = 0.6 mm/t
~ 300HB
For impact
resistance
AH3035 MJ 100 - 200 0.5 - 1.2 0.5 - 1.5 0.1
2,980 4,770 2,650 4,240 2,390 5,740 7,650
Vc = 150 m/min, fz = 0.8 mm/t
Prehardened steel
NAK80, PX5, etc.
30 ~
40HRC
-
AH3035 ML 100 - 200 0.5 - 0.7 0.5 - 1 0.1
2,980 3,580 2,650 3,180 2,390 4,300 5,740
Vc = 150 m/min, fz = 0.6 mm/t
Stainless steel
X5CrNi18-10,
X5CrNiMo17-12-2, etc.
~ 200HB
First choice
AH130 ML 100 - 150 0.3 - 0.5 0.3 - 0.7 0.08
2,390 1,910 2,120 1,700 1,910 2,290 3,060
Vc = 120 m/min, fz = 0.4 mm/t
~ 200HB
For impact
resistance
AH130 MJ 100 - 150 0.3 - 0.8 0.3 - 0.8 0.08
2,390 2,390 2,120 2,120 1,910 2,870 3,820
Vc = 120 m/min, fz = 0.5 mm/t
Grey cast iron
GG25, GGG30, etc.
150 ~
250HB
First choice
AH725 MJ 100 - 300 0.5 - 1.2 0.5 - 1.5 0.1
3,980 6,370 3,540 5,660 3,180 7,630 10,180
Vc = 200 m/min, fz = 0.8 mm/t
150 ~
250HB
For low
cutting force
AH725 ML 100 - 300 0.5 - 0.7 0.5 - 1 0.1
3,980 4,780 3,540 4,250 3,180 5,720 7,630
Vc = 200 m/min, fz = 0.6 mm/t
Ductile cast iron
GGG40, etc.
150 ~
250HB
First choice
AH725 MJ 80 - 200 0.5 - 1.2 0.5 - 1.5 0.1
2,980 4,770 2,650 4,240 2,390 5,740 7,650
Vc = 150 m/min, fz = 0.8 mm/t
150 ~
250HB
For low
cutting force
AH725 ML 80 - 200 0.5 - 0.7 0.5 - 1 0.1
2,980 3,580 2,650 3,180 2,390 4,300 5,740
Vc = 150 m/min, fz = 0.6 mm/t
Titanium alloys
Ti-6AI-4V, etc.
~ 40HRC -
AH725 ML 30 - 60 0.3 - 0.5 0.3 - 0.7 0.08
800 640 710 570 640 770 1,020
Vc = 40 m/min, fz = 0.4 mm/t
Heat-resistant alloys
Inconel, Hastelloy, etc.
~ 40HRC -
AH725 MJ 20 - 50 0.1 - 0.2 0.1 - 0.3 0.05
600 180 530 160 480 216 290
Vc = 30 m/min, fz = 0.15 mm/t
Hardened
steel
X40CrMoV5-1,
etc.
40 ~
50HRC
First choice
AH3035
MJ 80 - 130 0.1 - 0.2 0.1 - 0.3 0.05
1,990 600 1,770 530 1,590 720 950
For wear
resistance
AH725
Vc = 100 m/min, fz = 0.15 mm/t
X153CrMoV12,
etc.
50 ~
60HRC
First choice
AH725
MJ 50 - 70 0.03 -
0.05
0.03 -
0.07 0.03
1,190 100 1,060 80 950 114 150
For impact
resistance
AH3035
Vc = 60 m/min, fz = 0.04 mm/t
STANDARD CUTTING CONDITIONS TXN03/EXN03/HXN03
When chips stay in the cutting zone during slotting or pocketing, use air
blast to remove chips from the work area.
Tool overhang length must be as short as possible to avoid chatter. When
the tool overhang length is long, decrease the number of revolutions and
feed.
0.5
0.8 1
1.5
1
0.7
0.5
0.3
0
1
1.2
3
1
0.6
-
1.5
0.5
-
2
0.25 0.08
2.5
0.14 0.26
V
c = 100
~
300 m/min
V
c = 80
~
200 m/min
Tool geometry on program
The use of a standard or long shank
Tool dia.: ø
D
c = ø16 ~ 35 mm
Workpiece material: C55 (200HB)
L/D ratio of overhang
When using a long shank, please lower the cutting
conditions (
V
c,
f
z,
a
p) to 70% of the maximum conditions
for the standard shank.
When programming for CAM, the tool should be considered
as a radius cutters. Usually, the corner radius should be set as
R = 1.5 mm. If a larger radius is used, overcutting will occur.
The following table shows the amount left as uncut (t
1
) and
overcut (t
2
).
Each value in table is calculated theoretically at the maximum condition.
Amount left
as overcut
Standard shank: L/D ≤ 3
Long shank: L/D = 4
Standard shank
Long shank
Depth of cut:
a
p (mm)
Feed per tooth:
f
z (mm/t)
Corner
radius
Amount left
as uncut
Corner R
when
program-
ming
w
r
ε
R
t
1
17°
R
t
2
t
1
max.
a
p
Amount left
as overcut
Max. depth of cut
Corner R when
programming
Amount left
as uncut
Max. depth
of cut
max.
a
p
r
ε
W
(mm)
t
1
t
2
CAUTIONARY POINTS IN USE
Plung-
ing
Chip-
breaker
Cutting
speed
Feed per tooth: fz (mm/t)
Tool dia.: øDc (mm)
Workpiece material
Hard-
ness Priority Grade
1...,592,593,594,595,596,597,598,599,600,601 603,604,605,606,607,608,609,610,611,612,...1348
Powered by FlippingBook