Unknown - page 966

E016
2-e ective Drill
ISO
ø
D
c (mm)
V
c (m/min)
ø10 - ø11.9 ø12 - ø13.9 ø14 - ø15.9 ø16 - ø19.9 ø20 - ø25.9
80 - 140
0.15 - 0.28
0.18 - 0.3
0.2 - 0.35
0.25 - 0.45
0.25 - 0.45
70 - 120
0.15 - 0.28
0.18 - 0.3
0.2 - 0.35
0.25 - 0.45
0.25 - 0.45
70 - 120
0.14 - 0.28
0.16 - 0.32
0.18 - 0.35
0.23 - 0.4
0.25 - 0.45
40 - 90
0.14 - 0.28
0.16 - 0.32
0.18 - 0.35
0.23 - 0.4
0.25 - 0.45
30 - 70
0.12 - 0.18
0.14 - 0.2
0.16 - 0.24
0.16 - 0.26
0.18 - 0.3
80 - 180
0.2 - 0.35
0.25 - 0.4
0.3 - 0.45
0.35 - 0.55
0.35 - 0.6
80 - 140
0.2 - 0.35
0.25 - 0.4
0.3 - 0.45
0.35 - 0.55
0.35 - 0.6
80 - 220
0.25 - 0.4
0.3 - 0.45
0.35 - 0.5
0.4 - 0.60
0.5 - 0.75
20 - 50
0.08 - 0.15
0.1 - 0.28
0.12 - 0.2
0.14 - 0.22
0.18 - 0.27
20 - 50
0.08 - 0.13
0.1 - 0.15
0.12 - 0.18
0.12 - 0.22
0.14 - 0.22
STANDARD CUTTING CONDITIONS
- Cutting conditions in the above table show standard cutting conditions.
- Cutting conditions may change due to the rigidity and power of the machine
and the workpiece material.
Workpiece material
Cutting speed
Low carbon steels (C < 0.3)
E275A, E355D, C25, etc.
High carbon steels (C > 0.3)
C45, C55, etc.
Low alloy steels
18CrMo4, etc.
Alloy steels
42CrMo4, 20Cr4, etc.
Stainless steels
X5CrNi18-9,
X5CrNiMo17-12-2, etc.
Grey cast irons
250, etc.
Ductile cast irons
600-3, etc.
Titanium alloys
Ti-6Al-4V, etc.
Nickel-based alloys
Aluminium alloys
AlSi11Cu3, etc.
Feed:
f
(mm/rev)
- Machined hole diameter may change depending upon the rigidity of the
machine tool or cutting conditions.
- In case of L/D = 8,12 drill, the recommended range of cutting speeds and
feeds is between the minimum and median values listed above.
1...,956,957,958,959,960,961,962,963,964,965 967,968,969,970,971,972,973,974,975,976,...1348
Powered by FlippingBook