Unknown - page 1039

E089
Tungaloy
Indexable Drill
•When using the smaller side of the diameter range, the feed rate should be
set lower.
•When using DW insert for work materials of 40 HRC, the feed rate should be
set below 50%.
•For difficult-to-cut materials (heat-resistant alloys, etc.), the cutting speed
should be set 25% below that of carbon steels.
•For high-feed machining, apply a feed rate that is approximately 1.5 times the
standard feed conditions.
•High speed machining means cutting speeds over 150 m/min.
•When using DW insert for troubleshooting, use it within the range of standard
cutting conditions.
•DG type chipbreaker is suitable for heavy machines that have low-rpm spindles.
If chatter occurs, a lower feed rate is recommended.
STANDARD CUTTING CONDITIONS
Standard cut t ing condi t ions for DG type chipbreaker
ISO
Workpiece material
Cutting
speed
Vc (m/min)
Series
L/D
Feed: f (mm/rev)
ø27 ~ ø32
ø33 ~ ø54
Low carbon steels (C < 0.3)
C15E4, E275A, E355D, etc.
60 - 180
2D, 3D
0.04 - 0.1
4D, 5D
RECOMMENDED INSERT
ISO Workpiece material First choice High feed High speed
Troubleshooting
Chipping
resistance
Wear
resistance
Surface
finish
Chip
control
Low carbon steel
(C ≤ 0.3%)
DS, AH6030
-
-
DS, AH725
-
DW, AH6030 DG, AH725
Carbon steel (C > 0.3%)
Alloy steels
DJ, AH6030 DW, AH6030 DJ, AH9030 DW, AH725 DJ, AH9030 DW, AH6030
-
Low alloy steel
DS, AH6030
-
-
DS, AH725
-
DW, AH6030
-
Stainless steel
DS, AH6030
-
-
DS, AH725
-
DW, AH6030 DG, AH725
Grey cast iron
DJ, AH9030 DW, AH9030
DJ, T1115
DW, AH725
-
DW, AH9030
-
Ductile cast iron
DJ, AH9030 DW, AH9030
-
DW, AH725
-
DW, AH9030
-
Aluminium alloys
DJ, AH725
DW, AH725 DS, AH6030
-
-
DW, AH725
DG, AH725
Titanium alloys
Heat-resistant alloys
DS, AH6030
-
-
DW, AH725
-
DW, AH725
DG, AH725
Hardened steel
DJ, AH9030 DW, AH9030
-
DW, AH725
-
DW, AH9030
-
ISO
Workpiece material
Cutting
speed
Vc (m/min)
Series
L/D
Feed: f (mm/rev)
ø12.5 ~ ø14.5 ø15 ~ ø17 ø17.5 ~ ø26 ø27 ~ ø32 ø33 ~ ø54
Low carbon steels (C < 0.3)
C15E4, E275A, E355D, etc.
160 - 320
2D, 3D 0.02 - 0.06
0.02 - 0.06
0.04 - 0.1
0.04 - 0.1
0.04 - 0.1
4D, 5D 0.02 - 0.06
0.02 - 0.06
0.04 - 0.1
0.04 - 0.1
0.04 - 0.1
Carbon steels (C > 0.3)
C45, C55, etc.
80 - 250
2D, 3D 0.04 - 0.1
0.04 - 0.12
0.06 - 0.13
0.06 - 0.15
0.08 - 0.18
4D, 5D 0.04 - 0.08
0.04- 0.08
0.06 - 0.1
0.06 - 0.12
0.08 - 0.14
Low alloy steels
18CrMo4, etc.
160 - 250
2D, 3D 0.04 - 0.08
0.04 - 0.08
0.06 - 0.12
0.06 - 0.12
0.06 - 0.14
4D, 5D 0.04 - 0.08
0.04 - 0.08
0.06 - 0.12
0.06 - 0.12
0.06 - 0.14
Alloy steels
42CrMo4, 20Cr4, etc.
80 - 200
2D, 3D 0.04 - 0.1
0.04 - 0.12
0.06 - 0.13
0.06 - 0.15
0.08 - 0.18
4D, 5D 0.04 - 0.08
0.04 - 0.08
0.06 - 0.1
0.06 - 0.12
0.08 - 0.14
Stainless steels (Austenitic)
X5CrNi18-9, X5CrNiMo17-12-2, etc.
100 - 200
2D, 3D 0.02 - 0.08
0.02 - 0.08
0.04 - 0.1
0.04 - 0.12
0.04 - 0.12
4D, 5D 0.02 - 0.08
0.02 - 0.08
0.04 - 0.1
0.04 - 0.12
0.04 - 0.12
Stainless steels
(Martensitic and ferritic)
X5CrNi18-9, X5CrNiMo17-12-2, etc.
100 - 220
2D, 3D 0.02 - 0.08
0.02 - 0.08
0.04 - 0.1
0.04 - 0.12
0.04 - 0.12
4D, 5D 0.02 - 0.08
0.02 - 0.08
0.04 - 0.1
0.04 - 0.12
0.04 - 0.12
Stainless steels
(Precipitation hardening)
X5CrNiCuNb16-4, etc.
80 - 120
2D, 3D 0.04 - 0.08
0.04 - 0.08
0.04 - 0.08
0.04 - 0.1
0.06 - 0.1
4D, 5D 0.04 - 0.08
0.04 - 0.08
0.04 - 0.08
0.04 - 0.1
0.06 - 0.1
Grey cast irons
250, etc.
80 - 250
2D, 3D 0.06 - 0.12
0.06 - 0.12
0.06 - 0.15
0.06 - 0.18
0.08 - 0.2
4D, 5D 0.06 - 0.1
0.06 - 0.1
0.06 - 0.12
0.06 - 0.14
0.08 - 0.16
Ductile cast irons
600-3, etc.
80 - 200
2D, 3D 0.04 - 0.12
0.04 - 0.12
0.06 - 0.15
0.06 - 0.18
0.08 - 0.2
4D, 5D 0.04 - 0.1
0.04 - 0.1
0.06 - 0.12
0.06 - 0.14
0.08 - 0.16
Aluminium alloys
AlCu4SiMg, AlSi11Cu3, etc.
200 - 400
2D, 3D 0.1 - 0.12
0.1 - 0.15
0.15 - 0.2
0.15 - 0.2
0.15 - 0.25
4D, 5D 0.08 - 0.12
0.08 - 0.12
0.12 - 0.16
0.12 - 0.16
0.12 - 0.2
Heat-resistant alloys
Inconel 718, etc.
20 - 60 2D, 3D 0.04 - 0.08
0.04 - 0.08
0.04 - 0.1
0.04 - 0.1
0.04 - 0.1
20 - 60 4D, 5D 0.04 - 0.08
0.04 - 0.08
0.04 - 0.1
0.04 - 0.1
0.04 - 0.1
Titanium alloys
Ti-6Al-4V, etc.
40 - 120 2D, 3D 0.06 - 0.1
0.06 - 0.1
0.06 - 0.12
0.06 - 0.12
0.06 - 0.12
40 - 120 4D, 5D 0.06 - 0.08
0.06 - 0.08
0.06 - 0.1
0.06 - 0.1
0.06 - 0.1
Hardened steel
≥ 40HRC
40 - 100 2D, 3D 0.04 - 0.08
0.04 - 0.08
0.04 - 0.1
0.04 - 0.1
0.04 - 0.1
40 - 100 4D, 5D 0.04 - 0.08
0.04 - 0.08
0.04 - 0.08
0.04 - 0.08
0.04 - 0.08
1...,1029,1030,1031,1032,1033,1034,1035,1036,1037,1038 1040,1041,1042,1043,1044,1045,1046,1047,1048,1049,...1348
Powered by FlippingBook