D193
Tungaloy
Profile Milling
STANDARD CUTTING CONDITIONS
ISO
D8 D10 D12 D16 D20 D25 D30 D32
85 - 180 HB First choice AH725 ≤ 0.04D 180 - 260 0.15 0.2 0.2 0.25 0.25 0.3 0.35 0.35
85 - 180 HB
For wear
resistance AH710 ≤ 0.04D 180 - 260 0.15 0.2 0.2 0.25 0.25 0.3 0.35 0.35
180 - 280 HB First choice AH725 ≤ 0.03D 150 - 230 0.15 0.2 0.2 0.25 0.25 0.3 0.35 0.35
180 - 280 HB
For wear
resistance AH710 ≤ 0.03D 180 - 230 0.15 0.2 0.2 0.25 0.25 0.3 0.35 0.35
40 - 48 HRC First choice AH710 ≤ 0.03D 180 - 300 0.15 0.15 0.2 0.2 0.25 0.25 0.3 0.3
40 - 48 HRC
For fracture
resistance AH725 ≤ 0.03D 180 - 300 0.15 0.15 0.2 0.2 0.25 0.25 0.3 0.3
135 - 200 HB First choice AH725 ≤ 0.03D 100 - 250 0.1 0.15 0.2 0.2 0.25 0.25 0.3 0.3
150 - 240 HB First choice AH710 ≤ 0.04D 90 - 350
0.2 0.2 0.25 0.3 0.3 0.35 0.4 0.4
150 - 240 HB
For fracture
resistance AH725 ≤ 0.04D 90 - 350
0.2 0.2 0.25 0.3 0.3 0.35 0.4 0.4
-
First choice AH725 ≤ 0.03D 200 - 400 0.25 0.25 0.35
0.35 0.35
0.4 0.4 0.45
48 - 65 HRC First choice AH710 ≤ 0.02D 100 - 350 0.08 0.08 0.1
0.13 0.15
0.2 0.2 0.25
Workpiece
material
Grade
Feed per tooth
:
fz (mm/t)
Max.
depth of
cut
(mm)
Cutting
speed
Vc (m/min)
Hardness Priority
Low carbon steel,
alloy steel
High carbon steel,
alloy steel
Prehardened steel
Die & mold tool steel
Stainless steel
Cast iron
Aluminium
High hardened steel
How to clamp the insert
1. Clear chips and dust from the pocket.
2. Place the insert in the pocket. The insert can be placed only in one direction.
3. Tighten the screw while pressing the insert into the pocket.
How to check the run-out
1. Clamp the insert on the shank.
2. Clamp the shank on a high-precision arbor.
3. Measure the run-out on tool presetter or by dial gauge.
Notes:
1. Due to the helical cutting edge, it is important that the
run-out is inspected with the insert clamped on the shank.
2. Do not use micrometer or caliper to inspect the insert diameter as inaccurate dimensions may be provided.
· Remove excessive chip accumulation with an air blast.
· For the operation with depth of cut which varies (ex.casting skin) and
machining of workpiece materials with interrupted surface, the feed per tooth
(fz) should be set to the lower recommended value shown in the above table.
· Cutting conditions maybe limited depending on machine power, workpiece
rigidity, and spindle output. When the cutting width, depth, or overhang
length is large, set Vc and fz to the lower recommended values and check the
machine power and vibration.