D077
Tungaloy
Shoulder Milling
STANDARD CUTTING CONDITIONS TPW / EPW13 TYPE
Notes:
When machining at large depth of cut or large cutting width,
V
c and
f
z should be reduced.
As a rule, dry machining (including air blow) is recommended. But, for excessive chip
welding, such as when machining stainless steels, use a water soluble cutting fluid. In this
case, use AH140 and set the cutting speed to
Vc
≤
100 m/min.
When machining mild steel, carbon steel or alloy steel in wet conditions the T3130 is
recommended. In this case,
V
c and
f
z should be reduced.
TPW13 type can not be used for ramping, plunging and drilling.
ISO
Workpiece
material
Recommended
insert grade
Cutting speed
Vc (m/min)
Roughing (Depth of cut: ap ≥ 1.0 mm) Light cutting to finishing (Depth of cut: ap ≥ 1.0 mm)
Feed per tooth: fz (mm/t)
Feed per tooth: fz (mm/t)
MJ
ML
MS AJ
MJ
ML
MS AJ
Mild steels
Low carbon steels
< 180HB
AH120
(First choice)
100 - 270 0.05 - 0.25 0.05 - 0.2
-
-
0.05 - 0.2 0.05 - 0.18 -
-
T3130
(Priority on wear resistance)
150 - 300 0.05 - 0.25 -
-
-
0.05 - 0.2
-
-
-
AH130 / AH140
(Priority on impact resistance)
80 - 180 0.05 - 0.25 -
0.05 - 0.2
-
0.05 - 0.2
-
0.05 - 0.18 -
NS740
(Priority on surface finish)
100 - 300 0.05 - 0.15 -
-
-
0.05 - 0.12 -
-
-
Carbon steels
Alloy steels
< 300HB
AH120
(First choice)
100 - 230 0.05 - 0.2 0.05 - 0.15 -
-
0.05 - 0.18 0.05 - 0.12 -
-
T3130
(Priority on wear resistance)
150 - 280 0.05 - 0.2
-
-
-
0.05 - 0.18 -
-
-
AH130 / AH140
(Priority on impact resistance)
80 - 150 0.05 - 0.2
-
-
-
0.05 - 0.18 -
-
-
NS740
(Priority on surface finish)
100 - 230 0.05 - 0.15 -
-
-
0.05 - 0.12 -
-
-
Die steels
< 30HRC
AH120
(First choice)
100 - 180 0.05 - 0.15 0.05 - 0.12 -
-
0.05 - 0.12 0.05 - 0.1
-
-
T3130
(Priority on wear resistance)
100 - 180 0.05 - 0.15 -
-
-
0.05 - 0.12 -
-
-
Stainless
steels
< 50HB
AH130 / AH140
(First choice)
80 - 200 0.05 - 0.2
-
0.05 - 0.18 -
0.05 - 0.18 -
0.05 - 0.15 -
AH120
(Priority on wear resistance)
150 - 250 0.05 - 0.2 0.05 - 0.15 -
-
0.05 - 0.18 0.05 - 0.12 -
-
Grey cast irons
Ductile cast irons
T1215
(First choice)
100 - 250 0.05 - 0.2
-
-
-
0.05 - 0.18 -
-
-
AH120
(Priority on impact resistance)
100 - 250 0.05 - 0.2 0.05 - 0.15 -
-
0.05 - 0.18 0.05 - 0.12 -
-
Aluminium alloys
Si < 13 %
DS1100 / KS05F
(First choice)
300 - 1000 -
-
-
0.05 - 0.2
-
-
-
0.05 - 0.2
Aluminium alloys
Si ≥ 13 %
DS1100 / KS05F
(First choice)
80 - 300
-
-
-
0.05 - 0.2
-
-
-
0.05 - 0.2
Copper alloys
DS1100 / KS05F
(First choice)
200 - 500
-
-
-
0.05 - 0.2
-
-
-
0.05 - 0.2