Unknown - page 621

D029
Tungaloy
High-Feed Milling
STANDARD CUTTING CONDITIONS
ISO Workpiece
material
Insert
grade
Cutting speed
Vc (m/min)
Feed per tooth
fz (mm/t)
ø20, 21
(z = 2)
ø25, 26
(z = 2)
ø32, 33
(z = 2, 3)
ø40
(z = 3)
ø63
(z = 5, 6)
ø80
(z = 6, 7)
Carbon Steels
C50, etc.
< 300HB
AH120
(T3130)
100 ~ 250 0.5 ~ 2
Vc = 150 m/min, fz = 0.8 mm/t
ap =1 mm, ae = 1D mm
Vc = 150 m/min, fz = 1 mm/t
ap = 1 mm, ae = 1D mm
When plunging in small depth: fz = 0.2 mm/t
Alloy steels
42CrMo4etc, etc.
< 300 HB
AH120
(T3130)
100 ~ 200 0.5 ~ 2
Vc = 130 m/min, fz = 0.8 mm/t
ap = 1 mm, ae = 1D mm
Vc = 130 m/min, fz = 1 mm/t
ap = 1 mm, ae = 1D mm
When plunging in small depth: fz = 0.2 mm/t
Prehardened steels
NAK80, PX5,
X96CrMoV12, etc.
30 ~ 40HRC
AH120
(T3130)
80 ~ 150
0.5 ~ 1
Vc = 100 m/min, fz = 0.5 mm/t
ap = 1 mm, ae = 1D mm
Vc = 100 m/min, fz = 0.5 mm/t
ap = 1 mm, ae = 1D mm
When plunging in small depth: fz = 0.1 mm/t
Stainless steels
X5CrNi18 9, etc.
AH130
AH140
100 ~ 200 0.5 ~ 2
Vc = 130 m/min, fz = 0.8 mm/t
ap = 1 mm, ae = 1D mm
Vc = 130 m/min, fz = 1 mm/t
ap = 1 mm, ae = 1D mm
When plunging in small depth: fz = 0.2 mm/t
Cast irons
250, etc.
AH120 100 ~ 250 0.8 ~ 2.5
Vc = 150 m/min, fz = 1 mm/t
ap = 1 mm, ae = 1D mm
Vc = 180 m/min, fz = 1.5 mm/t
ap = 1 mm, ae = 1D mm
When plunging in small depth: fz = 0.2 mm/t
Hard materials
X153CrMoV12, etc.
40 ~ 50HRC
AH730 50 ~ 80
0.5 ~ 1
Vc = 70 m/min, fz = 0.7 mm/t, ap = 0.7 mm, ae = 1D mm
When plunging in small depth: fz = 0.1 mm/t
Note: •The above values of cutting speed show the standard speed when overhang length of tool is below 3D. The cutting speed and the feed rate should be
set at the lower limit values when overhang length of tool exceeds 3D.
•Thick and heavy chips are discharged by these TAC mills. Use internal air supply or air-blowing in order to prevent tool failure.
ISO Workpiece
material
Insert
grade
Cutting speed
Vc (m/min)
Feed per tooth
fz (mm/t)
ø40
(z = 2)
ø50
(z = 3)
ø63
(z = 4)
ø80
(z = 5)
ø100
(z = 6)
Carbon Steels
C50, etc.
< 300HB
AH120
(T3130)
100 ~ 250 0.5 ~ 2
Vc
= 180 m/min,
fz
= 1 mm/t
ap
= 1 mm,
ae
= 40 mm
Vc
= 200 m/min,
fz
= 1.5 mm/t
ap
= 1 mm,
ae
= 1D mm
When plunging in small depth:
fz
= 0.2 mm/t
Alloy steels
42CrMo4, etc.
< 300 HB
AH120
(T3130)
100 ~ 200 0.5 ~ 2
Vc
= 130 m/min,
fz
= 1 mm/t
ap
= 1 mm,
ae
= 40 mm
Vc
= 150 m/min,
fz
= 1.5 mm/t
ap
= 1 mm,
ae
= 1D mm
When plunging in small depth:
fz
= 0.2 mm/t
Prehardened steels
NAK80, PX5,
X96CrMoV12, etc.
30 ~ 40HRC
AH120
(T3130)
80 ~ 150
0.5 ~ 1
Vc
= 100 m/min,
fz
= 0.5 mm/t
ap
= 1 mm,
ae
= 40 mm
Vc
= 120 m/min,
fz
= 0.8 mm/t
ap
= 1 mm,
ae
= 1D mm
When plunging in small depth:
fz
= 0.1 mm/t
Stainless steels
X5CrNi18 9, etc.
AH130
AH140
100 ~ 200 0.5 ~ 2
Vc
= 130 m/min,
fz
= 1 mm/t
ap
= 1 mm,
ae
= 40 mm
Vc
= 150 m/min,
fz
= 1.5 mm/t
ap
= 1 mm,
ae
= 1D mm
When plunging in small depth:
fz
= 0.2 mm/t
Cast irons
250, etc.
AH120 150 ~ 250 0.8 ~ 2.5
Vc
= 180 m/min,
fz
= 1.5 mm/t
ap
= 1 mm,
ae
= 40 mm
Vc
= 200 m/min,
fz
= 2 mm/t
ap
= 1 mm,
ae
= 1D mm
When plunging in small depth:
fz
= 0.2 mm/t
Hard materials
X153CrMoV12, etc.
40 ~ 50HRC
AH730 50 ~ 80
0.5 ~ 1
Vc
= 70 m/min,
fz
= 0.7 mm/t,
ap
= 0.7 mm,
ae
= 1D mm
When plunging in small depth:
fz
= 0.1 mm/t
05·06 type
08 type
1...,611,612,613,614,615,616,617,618,619,620 622,623,624,625,626,627,628,629,630,631,...1348
Powered by FlippingBook