Unknown - page 431

Tungaloy
B415
º
º
º
º
º
º
º
º
º
º
º
º
º
º
º
º
º
º
º
º
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
3/8NPT
1/2NPT
3/4NPT
1NPT
1 1/4NPT
1 1/2NPT
2NPT
2 1/2NPT
3NPT
3 1/2NPT
4NPT
5NPT
6NPT
8NPT
10NPT
12NPT
14NPT
16NPT
18NPT
20NPT
24NPT
18
14
14
11.5
11.5
11.5
11.5
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1.41
1.81
1.81
2.21
2.21
2.21
2.21
3.175
3.175
3.175
3.175
3.175
3.175
3.175
3.175
3.175
3.175
3.175
3.175
3.175
3.175
1º37´
1º40´
1º19´
1º17´
1º00´
0º52´
0º41´
0º50´
0º40´
0º35´
0º31´
0º25´
0º21´
0º16´
0º13´
0º11´
0º10´
0º09´
0º08´
0º07´
0º06´
IR18NPT
IR14NPT
IR14NPT
IR115NPT
IR115NPT
IR115NPT
IR115NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
IR8NPT
SNR0006H06-2
SNR0006H06-3
SNR0008H06-2
SNR0008H06-3
SNR0016M16
SNR0016M16-2
SNR0016M16-3
CNR0020P16
CNR0025R16
CNR0032S16
(CNR0040T16)
(CNR0050U16)
SNR0006K06SC-2
SNR0006K06SC-3
SNR0008K06SC-2
SNR0008K06SC-3
SNR0016R16SC
SNR0016R16SC-2
(SNR0016R16SC-3)
TSNR0016Q16
TCNR0020R16DT
TCNR0025S16DT
(TCNR0032T16DT)
16IR
6IR
6IR
16IR
16IR
CNR0020P16
CNR0025R16
CNR0032S16
SNR0020Q22
SNR0020Q22-2
CNR0025R22
(CNR0050U27)
TCNR0025S22DT
(TCNR0032T22DT)
3/8
7/16
1/2
5/8
3/4
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2
1-3/4
2
12
12
10
8
6
6
5
5
5
4
4
4
4
2.12
2.12
2.54
3.18
4.23
4.23
5.08
5.08
5.08
6.35
6.35
6.35
6.35
8.465
10.053
11.43
14.274
16.934
20.109
22.86
26.035
29.21
31.75
34.925
41.275
47.625
IR12ACME
IR12ACME
IR10ACME
IR8ACME
IR6ACME
IR6ACME
IR5ACME
IR5ACME
IR5ACME
IR4ACME
IR4ACME
IR4ACME
IR4ACME
4º33´
3º50´
4º03´
4º03´
4º33´
3º50´
4º03´
3º33´
3º10´
3º39´
3º19´
2º48´
2º26´
16IR
22IR
27IR
16IR
22IR
16IR
TSNR0016Q16
SNR0016M16-2
TCNR0020R16DT
SNR0016R16SC-3
SNR0016M16-3
SNR0016M16
SNR0020Q22-3
CNR0032S22
CNR0040T27
SNR0016R16SC
SNR0016R16SC-2
Nominal size
TPI
Pitch
Lead angle
Shank material
Steel shank
Carbide shank
“Tsuppari-Ichiban”
Insert size
Holder Cat.
No.
Insert Cat.
No.
Nominal size
TPI
Pitch
Pitch diameter
Lead angle
Shank material
Steel shank
Carbide shank “Tsuppari-Ichiban”
Insert size
Holder Cat.
No.
Insert Cat.
No.
Because this thread standard is characterized with large pitch and small diameter, (that is a large lead angle) the standard inserts and toolholders can not
be used for machining this thread type. The application is limited to outside of the standard.
/
: Change the shim to AN16-0
/
: Change the shim to AN16-0DT
Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.
29° trapezoidal thread (ACME)
National taper pipe thread (NPT)
Threading Tool
1...,421,422,423,424,425,426,427,428,429,430 432,433,434,435,436,437,438,439,440,441,...1348
Powered by FlippingBook