Unknown - page 637

D045
Tungaloy
Shoulder Milling
STANDARD CUTTING CONDITIONS
ISO
- 200 HB
AH3135
100 - 250
100 - 250
0.08 - 0.18
0.08 - 0.22
200 - 300 HB AH3135
100 - 200
100 - 270
0.08 - 0.14
0.08 - 0.18
200 - 300 HB AH3135
100 - 150
100 - 180
0.08 - 0.14
0.08 - 0.18
-
AH3135
80 - 200
90 - 200
0.08 - 0.15
0.08 - 0.18
150 - 250 HB
AH120
T1215
100 - 250
150 - 250
140 - 250
150 - 250
0.10 - 0.18
0.08 - 0.22
150 - 250 HB
AH120
T1215
80 - 200
150 - 250
110 - 200
150 - 250
0.10 - 0.18
0.08 - 0.22
-
AH120
20 - 60
20 - 60
0.00 - 0.14
0.06 - 0.15
-
AH120
20 - 40
20 - 40
0.05 - 0.12
0.06 - 0.13
TLA10
TLA15
TLA10
TLA15
TLA (Roughing type)
STANDARD CUTTING CONDITIONS
ISO
- 200 HB AH3135 100 - 220 100 - 250 100 - 250 0.05 - 0.15 0.08 - 0.2 0.08 - 0.25
200 - 300 HB AH3135 100 - 170 100 - 200 100 - 230 0.05 - 0.12 0.08 - 0.15 0.08 - 0.2
200 - 300 HB AH3135 100 - 170 100 - 200 100 - 230 0.05 - 0.12 0.08 - 0.15 0.08 - 0.2
30 - 40 HRC AH3135 100 - 120 100 -150 100 - 180 0.05 - 0.12 0.08 - 0.15 0.08 - 0.2
-
AH3135 80 - 150 80 - 200 90 - 200 0.05 - 0.15 0.08 - 0.2 0.08 - 0.2
150 - 250 HB
AH120
T1215
100 - 200
150 - 250
100 - 250
150 - 300
140 - 250
200 - 300
0.05 - 0.15 0.08 - 0.2 0.08 - 0.25
150 - 250 HB
AH120
T1215
80 - 150
100 - 200
80 - 200
130 - 250
110 - 200
150 - 250
0.05 - 0.15 0.08 - 0.2 0.08 - 0.25
-
AH120
20 - 50
20 - 60
20 - 60 0.05 - 0.1 0.08 - 0.15 0.08 - 0.18
-
AH120
20 - 35
20 - 40
20 - 40 0.03 - 0.08 0.05 - 0.13 0.07 - 0.15
TPA/EPA/HPA
T/E/HPA06 T/E/HPA10 T/E/HPA15 T/E/HPA06 T/E/HPA10 T/EPA15
· Remove excessive chip accumulation with an air blast.
· For the operation with depth of cut which varies (ex.casting skin) and
machining of workpiece materials with interrupted surface, the feed per tooth
(fz) should be set to the lower recommended value shown in the above table.
· Cutting conditions maybe limited depending on machine power, workpiece
rigidity, and spindle output. When the cutting width, depth, or overhang
length is large, set Vc and fz to the lower recommended values and check the
machine power and vibration.
Note: When you use the NMJ chipbreaker, please set up the feed less than 0.15 mm/t.
Cutting speed:
Vc
(m/min)
Feed per tooth: fz (mm/t)
Stainless steel
X5CrNi18-9, etc.
Grey cast iron
250, etc.
Ductile cast iron
450-10S, etc.
Titanium alloys
Ti-6Al-4V, etc.
Heat-resistant alloys
Inconel 718, etc.
Workpiece material
Grade
Hardness
Note: When you use the NMJ chipbreaker, please set up the feed less than 0.15 mm/t.
Low carbon steel
E275A, C15E4, etc.
High carbon steel
C45, etc.
Alloy steel
42CrMo4, etc.
Cutting speed:
Vc
(m/min)
Feed per tooth: fz (mm/t)
Low carbon steel
E275A, C15E4, etc.
High carbon steel
C45, etc.
Alloy steel
42CrMo4, etc.
Tool steel
X40CrMoV5-1, etc.
Stainless steel
X5CrNi18-9, etc.
Grey cast iron
250, etc.
Ductile cast iron
450-10S, etc.
Titanium alloys
Ti-6Al-4V, etc.
Heat-resistant alloys
Inconel 718, etc.
Workpiece material
Grade
Hardness
1...,627,628,629,630,631,632,633,634,635,636 638,639,640,641,642,643,644,645,646,647,...1348
Powered by FlippingBook