Unknown - page 1065

E115
Tungaloy
Deep Hole Drill
C20 ~ C30
210 ~ 250 (16) ~ 24 90
Refer
to Fig. 2
C30 ~ C55
260 ~ 310 26 ~ 33 70
C50 ~
320 ~ 375 34 ~ 40 50
C55 ~
380 ~ 440 41 ~ 47 40
150 ~ 230 ~ (20)
90
Refer
to Fig. 2
240 ~ 310 23 ~ 33 70
Refer
to Fig. 2
315 ~ 370 34 ~ 40 50
Refer
to Fig. 3
380 ~ 440 40 ~ 47 40
450 ~ 500 48 ~ 51 30
140 ~ 180 ~ (8)
100
Refer
to Fig. 2
190 ~ 240 (11) ~ 22 90
150 ~ 200 ~ (13)
70
Refer
to Fig. 3
210 ~ 300 (16) ~ 32 50
150 ~ 200 ~ (13)
70
Refer
to Fig. 3
160 ~ 220 ~ (18)
50
160 ~ 220 ~ (18)
70
300 ~ 350 32 ~ 38 50
110 ~ 180
90
Refer
to Fig. 4
190 ~ 220
80
220 ~ 260
70
120 ~ 170
80
Refer
to Fig. 5
180 ~ 240
65
240 ~ 280
55
260 ~ 320
40
110 ~ 180
90
190 ~ 220
80
220 ~ 260
70
180
Refer
to Fig. 4
40 ~ 100
120 ~ 160
< 150
Refer
to Fig. 4
160 ~ 205
< 150
Refer
to Fig. 5
150 ~ 210
70
Refer
to Fig. 3
20
210 ~ 285 (16) ~ 30 50
HB HRC
160 - 190 (5) - (11)
130
Refer
to Fig. 1
C10C ~ C15
C30 ~ C50
200 - 230 (12) - 20 100
C30 ~ C50
250 - 300 25 - 32 80
110 ~ 120
130
C10 ~ C30
C10 ~ C50
120 ~ 185 ~ (9)
120
C50 ~
170 ~ 200 (5) ~ (13)
100
ISO
0.05
0.04
0.03
0.02
0.01
0.05
0.04
0.03
0.02
0.01
2 3 4 5 6 8 10
20 30
2 3 4 5 6 8 10
20 30
0.04
0.03
0.02
0.01
2 3 4 5 6 8 10
20 30
0.1
0.08
0.06
0.04
0.02
0.01
2 3 4 5 6 8 10
20 30
0.1
0.08
0.06
0.04
0.02
0.01
2 3 4 5 6 8 10
20 30
10
9
8
7
6
5
4
3
2
1
180
160
140
120
100
80
60
40
20
2 3 4 5 678910
20 304050
STANDARD CUTTING CONDITIONS
Cold drawn
Free-cutting carbon
steels
Workpiece
material
Hardness
Heat
treatment
Cold drawn
Hardened and
tempered
Carbon steels
Cutting
speed
Vc (m/min)
Feed
f (mm/rev)
• No. of revolutions:
n
(min
-1
) = Cutting speed:
V
c (m/min)
1000
3.14
Tool diameter: ø
D
c (mm)
• Feed speed:
V
f (mm/min) = No. of revolutions:
n
Feed:
f
(mm/rev)
Annealed
Annealed
Annealed
Hardened and
tempered
Hardened and
tempered
Hardened and
tempered
Hardened and
tempered
Annealed
Annealed
or
Hardened and
tempered
Annealed
Annealed
Annealed
Annealed
Annealed
Annealed
Hardened and
tempered
Annealed
Annealed
Austenitic
X5CrNi18-9
Alloy steels
Cast steels
Tool steels
Stainless steels
Ferritic
X6Cr17
Martensitic
X12Cr13
Bearing steels
High-resistant steels
High speed steels
Grey cast irons
Ductile cast irons
Malleable cast irons
Cast aluminium alloys
Aluminium die cast alloys
Copper alloys
5000load
Fig. 2 Alloy steels
Drill diameter: ø
D
c
Drill diameter: ø
D
c
Fig. 1 Carbon steels
Feed:
f
(mm/rev)
Feed:
f
(mm/rev)
Fig. 3 Tool steels and other
special steels
Drill diameter: ø
D
c
Feed:
f
(mm/rev)
Fig. 4 Cast irons, aluminium
alloys
Drill diameter: ø
D
c
Feed:
f
(mm/rev)
Fig. 5 Ductile and malleable
cast irons
Drill diameter: ø
D
c
Feed:
f
(mm/rev)
Pressure
Supply volume
Drill diameter ø
D
c
Coolant pressure (MPa)
Coolant supply volume
(
R
/min)
Coolant suppl y pressure and volume
1...,1055,1056,1057,1058,1059,1060,1061,1062,1063,1064 1066,1067,1068,1069,1070,1071,1072,1073,1074,1075,...1348
Powered by FlippingBook