Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/257 Drilling Drill out damaged thread with normal jobber drills. Boring out is not required for spark plug threads - the combined drilling and cutting tool should be used. Please note that larger holes are required for taps. Control the tap and thread bolt for the same thread and gradient. Thread cut the mounting thread in the bored out hole with the special V-COIL taps. The use of cutting oil is recommended. Installing the threaded insert: Place the insert on the tool and make sure that the carrier pin is in the slot opening and then make the right setting with the adjustment ring. Then turn in the threaded insert in the thread direction applying light pressure. Do not turn against the running direction, as the pin can break off. Breaking the pin: After installation, take the insertion tool out and remove the carrier pin with the pin breaker. The pin should be removed with long nose pliers for larger dimensions and spark plug threads. After completing these steps, a thread is produced that is often better and stronger than the original thread due to the narrow and exact tolerances as well as the spring thread forming. Application: Thread armouring of materials with low shearing resistance e.g. aluminium and magnesium alloys, in mechanical engineering, in automobile, electro and medical technology and in aviation and aerospace. Thread repair of damaged or worn threads. Reject recovery. Scope of delivery: In plastic cassette: thread extractor, jobber drill in core hole dimensions, tap and thread inserts (1.5 x D). Set content 1652 Order No. € M5–M12 172.00 …0050 M6–M10 109.00 …0075 M6–M12 + M14 x 1.25 189.00 …0100 (W159) V-COIL thread repair assortment Design: Standard threaded insert free running made of stainless steel. Thread insert 1652 0160 – 0260 1.0 x D, according to DIN 8140. 1652 0214 – 0624 1.5 x D, according to DIN 8140. 1653 0300 – 0360 2.0 x D, according to DIN 8140. 1653 0840 – 1640 For spark plug thread. Size 1652 Order No. € M2 100 ∆ 56.90 …0160 M2.5 100 ∆ 16.40 …0180 M3 100 ∆ 16.40 …0200 M4 100 ∆ 16.40 …0210 M5 100 ∆ 19.70 …0220 M6 100 ∆ 20.80 …0230 M8 100 ∆ 21.90 …0240 M10 100 ∆ 27.30 …0250 M12 100 ∆ 47.00 …0260 Δ Can only be supplied as a whole packaging unit. (W159) Size 1652 Order No. € M3 100 ∆ 18.60 …0590 M4 100 ∆ 18.60 …0595 M5 100 ∆ 15.30 …0600 M6 100 ∆ 16.40 …0605 MF8 x 1 100 ∆ 25.20 …0214 M8 100 ∆ 21.90 …0610 MF10 x 1 100 ∆ 30.60 …0245 M10 100 ∆ 30.60 …0615 M12 100 ∆ 52.50 …0620 MF14 x 1.25 50 ∆ 70.00 …0622 M14 50 ∆ 70.00 …0623 M16 50 ∆ 86.40 …0624 Δ Can only be supplied as a whole packaging unit. (W159) Size 1653 Order No. € M3 100 ∆ 19.70 …0300 M4 100 ∆ 19.70 …0310 M5 100 ∆ 21.90 …0320 M6 100 ∆ 25.20 …0330 M8 100 ∆ 30.60 …0340 M10 100 ∆ 35.00 …0350 M12 100 ∆ 59.00 …0360 Δ Can only be supplied as a whole packaging unit. (W159) Size Length of thread mm 1653 Order No. € MF14 x 1.25 8.4 50 ∆ 74.40 …0840 MF14 x 1.25 12.4 50 ∆ 74.40 …1240 MF14 x 1.25 16.4 50 ∆ 78.70 …1640 Δ Can only be supplied as a whole packaging unit. (W159) Dies and holding tools 1.6
RkJQdWJsaXNoZXIy NTg4MTI=