Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/255 Design: Very durable tool with spring tempered and adjustable fingers. The guide sleeve can be moved lengthways and therefore takes very high torsion forces. Application: For loosening and unscrewing broken taps with 3 slots (Order No. 1852) or 4 slots (Order No. 1848). The fingers are inserted into the slots on the broken tap and secured with the guide bush by sliding the upper retainer ring. The broken off tap piece is moved back and forth with a tap wrench until it loosens and can be screwed out. Thread BSW thread UNC/UNF thread 1852 1848 Order No. € € 1852 1848 1852 1848 M3 1/8 – No.5 – 36.50 – …0030 M4 5/ 32 5/ 32 No. 8 – 36.50 37.10 …0040 M5 3/ 16 3/ 16 – No. 8 36.50 37.10 …0050 M6 1/4 1/4 – – 38.30 37.10 …0060 M8 5/ 16 5/ 16 – – 39.90 39.90 …0080 (W178) (W178) Thread BSW thread UNC/UNF thread 1852 1848 Order No. € € 1852 1848 1852 1848 M10 3/8 3/8 – – 39.90 39.90 …0100 M12 1/2 1/2 – – 44.70 44.70 …0120 M14 9/ 16 – – – 61.40 – …0140 M16 5/8 5/8 – – 66.60 66.60 …0160 M20 – 3/ 4 – – – 85.90 …0200 (W178) (W178) Tap extractor 1852 For 3-slot tap. 1848 For 4-slot tap. Thread BSW thread UNC/UNF thread 1853 1849 Order No. € € 1853 1849 M3 1/ 8 No. 5 – 1.84 – …0030 M4 5/ 32 No. 8 – 1.84 1.84 …0040 M5 3/ 16 – No. 8 2.67 2.67 …0050 M6 1/ 4 – – 3.30 3.30 …0060 M8 5/ 16 – – 3.67 3.67 …0080 (W178) (W178) Thread BSW thread UNC/UNF thread 1853 1849 Order No. € € 1853 1849 M10 3/ 8 – – 3.67 3.67 …0100 M12 1/ 2 – – 4.78 4.78 …0120 M14 9/ 16 – – 5.50 – …0140 M16 5/ 8 – – 6.80 6.80 …0160 M20 3/ 4 – – – 7.70 …0200 (W178) (W178) Replacement finger set 1853 For 3-slot tap. 1849 For 4-slot tap. Design: Supplied in a sturdy plastic cassette, incl. respective tap extractors and the right replacement finger sets. Quantity Design Set content 1854 Order No. € 6-pc 3-slot M4; 5; 6; 8; 10; 12 256.50 …0010 10-piece 3-slot M3; 4; 5; 6; 8; 10; 12; 14; 16; 20 498.00 …0020 6-pc 4-slot M4; 5; 6; 8; 10, 12 256.50 …0030 10-piece 4-slot M4; 5; 6; 8; 10; 12; 14; 16; 20; 22 550.50 …0040 (W178) Tap extractor set Application: Extraction must take place dry at approx. 1500-3500 rpm. With use of the right tap bore-out tool, the core of the tap is quickly bored out and the rest of the tap can be cleanly blown out of the drill hole. The workpiece must be clamped very steadily so that movement does not happen at higher speeds. A centring must be produced first by starting the tap bore-out tool up several times if the tap has broken off at an angle. Only then boring out can be started. Furthermore, the chips should be removed by "air blow" several times. A vibration can be felt just before the end of the bore-out process. The extractor should now be removed. The new thread can then be cut with a tap. ∅ d1 h10 mm Thread Total length L1 mm Cutting edge length L2 mm 1854 Order No. € 3.3 M4 50 15 46.40 …0400 4.2 M5 50 15 48.50 …0500 5 M6 50 15 54.50 …0600 6.8 M8 60 20 73.20 …0800 (W176) ∅ d1 h10 mm Thread Total length L1 mm Cutting edge length L2 mm 1854 Order No. € 8.5 M10 70 25 92.70 …1000 10.2 M12 75 30 114.00 …1200 14 M16 100 40 192.50 …1600 17.5 M20 100 50 335.00 …2000 (W176) TiN TiN Tap borer Solid carbide N 3 DIN 6535-HA TiN L2 L1 d 2 d1 Dies and holding tools 1.6
RkJQdWJsaXNoZXIy NTg4MTI=