FORMAT_EN_2023-25_WCT_Light

All prices quoted are non-binding recommended prices. 1/254 Design: Made of steel, annealed and burnished (rust protected). The protruding and recessed squares are the same size. Application: For extending hand taps, hand reamers and other tools with a square receptacle Square mm Length mm For tap DIN 352 For tap DIN 5157 1870 Order No. € 2.1 60 M1–2.6 – 3.46 …0210 2.7 80 M3 – 3.47 …0270 3.4 95 M4 – 3.44 …0340 4.3 105 – – 4.95 …0430 4.9 110 M4,5–8 – 3.86 …0490 5.5 115 M9–10 G 1/8" 4.41 …0550 6.2 120 M11 – 4.87 …0620 7 125 M12 – 6.00 …0700 ​ (W176) Square mm Length mm For tap DIN 352 For tap DIN 5157 1870 Order No. € 8 125 – – 7.55 …0800 9 130 M14/16 G 1/4" + 3/8" 8.30 …0900 11 150 M18 – 12.35 …1100 12 155 M20 G 1/2" 15.85 …1200 14.5 175 M22–24 G 5/8" 21.60 …1450 16 180 M27 G 3/4" 23.40 …1600 18 200 M30 G 7/8" 27.30 …1800 20 220 M33 G 1" 35.10 …2000 ​ (W176) Tap extension DIN 377 Design: Made of steel, annealed and burnished (rust protected). The front end is designed as collets. Clamping takes place by tightening the knurled clamping nut. The rear part of the extension corresponds to DIN, use in quick-change inserts and tapping devices possible. Application: For thread cutting with extremely deep internal threads. Size L2 mm Total length L3 mm 1824 Order No. € 1 60 130 151.50 …0113 1 70 230 166.50 …0123 2 60 130 151.50 …0213 2 70 230 166.50 …0223 3 60 130 151.50 …0313 3 70 230 166.50 …0323 4 60 130 151.50 …0413 4 70 230 166.50 …0423 5 60 130 157.50 …0513 5 70 230 171.00 …0523 6 60 130 157.50 …0613 6 80 230 171.00 …0623 7 60 130 157.50 …0713 ​ (W031) Size L2 mm Total length L3 mm 1824 Order No. € 7 80 230 171.00 …0723 8 60 130 157.50 …0813 8 80 230 171.00 …0823 9 90 130 166.50 …0913 9 90 230 181.50 …0923 10 90 130 166.50 …1013 10 90 230 181.50 …1023 11 90 200 276.00 …1120 11 90 330 304.50 …1133 12 90 200 276.00 …1220 12 90 330 304.50 …1233 13 100 200 300.00 …1320 13 100 330 330.00 …1333 ​ (W031) Tap extension Size DIN 371 DIN 374/376 ​ Clamping Square ​ Square ​ ​ ​ ∅ d1 ∅ d1 ∅ d2 Length L1 K1 ∅ D3 K2 ∅ D4/D5 ​ ​ ​ ​ mm mm mm mm mm mm ​ 1 M2–M2.6 M4 2.8 22 2.1 6 4.9 6.1 ​ 2 M3 M4.5–M5 3.5 23 2.7 6 4.9 7.5 ​ 3 M4 M6 4.5 23 3.4 6 4.9 8.4 ​ 4 M4.5–M6 M8 6 26 4.9 7 5.5 12.1 ​ 5 M7 M9–M10 7 26 5.5 7 5.5 12.1 ​ 6 M8 M11 8 30 6.2 8 6.2 13 ​ 7 M9 M12 9 31 7 9 7 15 ​ 8 M10 – 10 33 8 10 8 15 ​ 9 – M14 11 36 9 11 9 18 ​ 10 – M16 12 36 9 12 9 18 ​ 11 – M18 14 42 11 14 11 22 ​ 12 – M20 16 42 12 16 12 22 ​ 13 – M22–M24 18 43 14.5 18 14.5 26 ​ 1824 Standard. Dies and holding tools 1.6

RkJQdWJsaXNoZXIy NTg4MTI=