Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 3/25 Design: From alloy case-hardened steel, with a core tensile strength of min. approx. 950 N/mm2 and a hardness depth of min. 0.5 mm. Taper to DIN 254. Taper angle tolerance: AT3 Taper surface roughness: Ra < 0.001 mm Drill tolerance: H5 Hardened: 58 ± 2 HRC Application: For mounting and holding tools with cylinder shank and side drive surface acc. to DIN 1835-B and DIN 6535-HB. Scope of delivery: Face chuck with integrated clamping screw, from Ø 25 mm with two clamping screws. D mm A mm D mm 3093 Order No. SK 40 € 6 50 25 46.30 …4006 8 50 28 44.30 …4008 10 50 35 44.30 …4010 12 50 42 44.30 …4012 14 50 44 44.30 …4014 16 63 48 44.30 …4016 18 63 50 44.30 …4018 20 63 52 44.30 …4020 25 80 65 48.30 …4025 32 80 72 54.40 …4032 (W050) d1 mm A mm D mm 3093 Order No. SK 50 € 6 63 25 74.40 …5006 8 63 28 72.40 …5008 10 63 35 72.40 …5010 12 63 42 72.40 …5012 14 63 44 72.40 …5014 16 63 48 72.40 …5016 18 63 50 72.40 …5018 20 63 52 72.40 …5020 25 80 65 78.40 …5025 32 80 72 84.50 …5032 (W050) Weldon system surface clamping chuck DIN 2080 A ≤ 10 µm Design: From alloy case-hardened steel, with a core tensile strength of min. approx. 950 N/mm2 and a hardness depth of min. 0.5 mm. Taper to DIN 254. Taper angle tolerance: AT3 Taper surface roughness: Ra < 0.001 mm Hardened: 58 ± 2 HRC Application: For mounting and holding tools with cylinder shank in collets acc. to DIN 6499 (ER) Scope of delivery: Collet chuck ER with clamping nut. Clamping range mm Collet A mm D mm 3095 Order No. SK 40 € 1–10 ER16 50 32 56.30 …4016 1–16 ER25 50 42 56.30 …4025 2–20 ER32 50 50 58.40 …4032 3–26 ER40 80 63 60.40 …4040 (W050) Clamping range mm Collet A mm D mm 3095 Order No. SK 50 € 2–20 ER32 63 50 90.50 …5032 3–26 ER40 63 63 90.50 …5040 (W050) Collet chuck, type ER DIN 2080 A ≤ 20 µm Design: From forged steel, with a core tensile strength of min. approx. 800 N/mm2 and a hardness depth of 0.8 mm. Taper to DIN 254. Taper angle tolerance: AT3 Taper surface roughness: Ra < 0.003 to 0.005 mm Hardened: 58 ± 2 HRC Application: For mounting and holding tools with longitudinal slot and crosswise slot. Scope of delivery: Combi face mill adaptor with cutting retaining screw, driving ring and keyed slot nut. D mm A mm L mm D mm 3096 Order No. SK 40 € 16 52 17 32 56.30 …4016 22 52 19 40 56.30 …4022 27 52 21 48 56.30 …4027 32 52 24 58 60.40 …4032 40 52 27 70 68.40 …4040 (W050) D mm A mm L mm D mm 3096 Order No. SK 50 € 16 55 17 32 74.40 …5016 22 55 19 40 74.40 …5022 27 55 21 48 76.40 …5027 32 55 24 58 78.40 …5032 40 55 27 70 86.50 …5040 (W050) Combination-face mill adaptor DIN 2080 A ≤ 5 µm Tool holders 3.1
RkJQdWJsaXNoZXIy NTg4MTI=