All prices quoted are non-binding recommended prices. 1/282 Design: Convex relieved. Application: Can be used for milling semi-circular grooves. Note: The cutters can be reground several times without the profile being changed. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 22 15 – 20 – – 18 20 – – 55 22 – – – – 2052 Radius r mm Tolerance mm ∅ d1 mm Width b mm Bore d2 = H7 mm Number of teeth STEEL < 700 N/mm2 fz mm 2052 Order No. € 1 ±0.05 50 2 16 14 0.08 75.70 …0001 1.5 ±0.05 50 3 16 14 0.08 75.70 …0004 2 ±0.05 50 4 16 14 0.08 75.70 …0007 2.5 ±0.08 63 5 22 12 0.1 75.10 …0010 3 ±0.08 63 6 22 12 0.1 77.60 …0013 3.5 ±0.08 63 7 22 12 0.1 80.90 …0016 4 ±0.08 63 8 22 12 0.1 82.90 …0019 4.5 ±0.08 63 9 22 12 0.1 92.80 …0022 5 ±0.08 63 10 22 12 0.1 110.50 …0025 5.5 ±0.08 80 11 27 12 0.12 117.50 …0028 6 ±0.08 80 12 27 12 0.12 128.00 …0031 6.5 ±0.08 80 13 27 12 0.12 139.50 …0034 7 ±0.08 80 14 27 12 0.12 142.00 …0037 7.5 ±0.08 80 15 27 12 0.12 144.50 …0040 8 ±0.08 80 16 27 12 0.12 155.50 …0043 8.5 ±0.12 100 17 32 12 0.14 170.00 …0046 9 ±0.12 100 18 32 12 0.14 186.00 …0049 10 ±0.12 100 20 32 12 0.14 222.50 …0052 (W204) bright Half-round router bit HSS DIN 138 bright Design: Fine diamond cut. Application: Can be used for notch or slot cutting. Right- and leftcutting. For excellent precision and clean milled surface. Low-vibration milling - especially for deep cuts. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 36 18 – 16 14 – 20 25 – – – 28 – – – – 2043 ∅ x width d1 x b1 mm Bore d2 = H7 mm Number of teeth STEEL < 700 N/mm2 fz mm 2043 Order No. € 63 x 1.6 22 28 0.06 81.20 …0001 63 x 2 22 28 0.06 71.90 …0004 63 x 2.5 22 28 0.06 73.40 …0007 63 x 3 22 28 0.06 75.50 …0010 63 x 4 22 28 0.06 81.10 …0013 80 x 1.6 27 32 0.07 89.40 …0016 80 x 2 27 32 0.07 86.90 …0019 80 x 2.5 27 32 0.07 88.30 …0022 80 x 3 27 32 0.07 89.50 …0025 80 x 4 27 32 0.07 95.80 …0028 100 x 1.6 32 36 0.08 107.00 …0031 100 x 2 32 36 0.08 106.50 …0034 100 x 2.5 32 36 0.08 103.00 …0037 100 x 3 32 36 0.08 103.50 …0040 100 x 4 32 36 0.08 111.50 …0043 (W203) ∅ x width d1 x b1 mm Bore d2 = H7 mm Number of teeth STEEL < 700 N/mm2 fz mm 2043 Order No. € 100 x 5 32 36 0.08 118.50 …0046 125 x 1.6 32 40 0.09 138.00 …0049 125 x 2 32 40 0.09 132.50 …0052 125 x 2.5 32 40 0.09 129.50 …0055 125 x 3 32 40 0.09 132.50 …0058 125 x 4 32 40 0.09 140.00 …0061 125 x 5 32 40 0.09 150.00 …0064 125 x 6 32 40 0.09 161.00 …0067 160 x 2 40 48 0.09 214.00 …0070 160 x 2.5 40 48 0.09 206.00 …0073 160 x 3 40 48 0.09 209.50 …0076 160 x 4 40 48 0.09 208.00 …0079 160 x 5 40 48 0.09 220.50 …0082 160 x 6 40 48 0.09 241.00 …0085 (W203) bright bright Narrow side milling cutter HSS Co5 N DIN 1834-A DIN 138 bright End mills HSS-E/HSS-E PM 1.8
RkJQdWJsaXNoZXIy NTg4MTI=