Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/11 Design: With precision ground point and narrow cross blade. With a side clearance angle of 12°/30°. Application: For precise drill positioning. Used for centring and chamfering thread holes in one step. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 20 10 6 – – – 15 5 3 30 30 20 3 – – – 1147 ∅ h8 mm Slot length mm Total length mm STEEL < 700 N/mm2 f mm/rev 1147 Order No. € 6 20 140 0.09 32.80 …0600 8 25 140 0.1 34.70 …0800 10 25 170 0.13 44.80 …1000 12 30 170 0.16 56.00 …1200 (W106) TiN NC spotting drill, with cylinder Shank, length HSS Co5 DIN 1835-B 90° TiN Design: Very sturdy model with precision ground point and narrow cross blade. With a side clearance angle of 12°/30°. From ∅ 6 mm with carrier surface according to DIN 1835-B. ∅ tolerance: h6. Application: Special drill for precise drill positioning. Used for centring and chamfering thread holes in one step. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 20 10 6 – – – 15 5 3 30 30 20 3 – – – 1143 20 10 6 – – – 15 5 3 30 30 20 3 – – – 1149 ∅ h8 mm Slot length mm Total length mm STEEL < 700 N/mm2 f mm/rev 1143 1149 Order No. € € 3 12 46 0.04 2.65 – …0300 4 12 55 0.05 3.06 – …0400 5 14 62 0.07 3.82 8.55 …0500 6 16 66 0.09 6.45 11.70 …0600 8 21 79 0.1 9.40 15.95 …0800 10 25 89 0.13 14.00 21.60 …1000 12 30 102 0.16 18.00 26.50 …1200 16 38 115 0.2 32.40 36.30 …1600 20 45 131 0.23 49.80 59.00 …2000 (W106) (W106) bright TiN NC spotting drill, with cylinder shank HSS Co5 DIN 1835-B 120° 1149 TiN 1143 bright _ _ Drills HSS/HSS-E 1.1
RkJQdWJsaXNoZXIy NTg4MTI=