All prices quoted are non-binding recommended prices. 1/140 Design: Centring up to Ø 3.7 mm on both sides with 90° full point, above with centring, with straight shank Ø for standardised assembling in hydraulic expansion and high-precision chucks. The clamping accuracy is significantly improved due to the narrow tolerance of the shanks. Reamer manufacturing tolerances: – Full diameter as well as 1/10 mm dimensions H7 – 1/100 mm dimensions from Ø 1.01 to 5.03 mm 0.000/+0.004 mm, above Ø 5.03 mm 0.000/+0.005 mm Application: For reaming through holes, also suitable for reaming blind holes due to the short point (from 3.8 mm). Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 14 12 8 6 5 4 10 8 4 20 18 – – – – – 1545 Nominal-∅ mm Cutting edge length mm Total length mm Shank ∅ h6 mm 1545 Order No. € 1 6 35 1 19.65 …0100 1.01 6 35 1 19.65 …0101 1.02 6 35 1 19.65 …0102 1.03 6 35 1 19.65 …0103 1.5 8 40 2 14.45 …0150 1.51 9 43 2 16.95 …0151 1.52 9 43 2 16.95 …0152 1.53 9 43 2 16.95 …0153 1.6 9 43 2 16.50 …0160 1.7 9 43 2 16.50 …0170 1.8 10 46 2 16.50 …0180 1.9 10 46 2 16.50 …0190 1.97 11 49 2 17.95 …0197 1.98 11 49 2 17.95 …0198 (W144) Nominal-∅ mm Cutting edge length mm Total length mm Shank ∅ h6 mm 1545 Order No. € 1.99 11 49 2 17.95 …0199 2 11 49 2 14.55 …0200 2.01 11 49 2 18.30 …0201 2.02 11 49 2 18.30 …0202 2.03 11 49 2 18.30 …0203 2.1 11 49 2 16.75 …0210 2.2 12 53 2 16.75 …0220 2.3 12 53 3 16.75 …0230 2.4 14 57 3 16.75 …0240 2.47 14 57 3 18.30 …0247 2.48 14 57 3 18.30 …0248 2.49 14 57 3 18.30 …0249 2.5 14 57 3 14.25 …0250 2.51 14 57 3 18.30 …0251 (W144) bright bright NC, machine reamer Continued on next page HSS-E ≈DIN 212 bright Design: Short point and uneven tooth pitch. This achieves clean and exact drilling. With morse taper shank. Application: Only for reaming through holes. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 10 8 8 4 2 4 6 5 4 20 18 – – – – – 1537 12 10 10 – – – 12 10 – – – – – – – – 1541 Nominal-∅ mm Cutting edge length mm Total length mm MT 1537 1541 Order No. € € 10 38 168 1 36.90 C◊ …1000 11 41 175 1 40.40 – …1100 12 44 182 1 39.60 C◊ …1200 13 44 182 1 41.70 – …1300 14 47 189 1 42.40 109.00 …1400 15 50 204 2 51.50 C◊ …1500 16 52 210 2 52.20 136.50 …1600 17 54 214 2 55.80 – …1700 18 56 219 2 57.90 151.00 …1800 (W140) (W141) Nominal-∅ mm Cutting edge length mm Total length mm MT 1537 1541 Order No. € € 19 58 223 2 61.50 – …1900 20 60 228 2 61.50 160.00 …2000 22 64 237 2 69.10 – …2200 24 68 268 3 81.90 – …2400 25 68 268 3 84.00 – …2500 26 70 273 3 90.50 – …2600 28 71 277 3 99.60 – …2800 30 73 281 3 103.00 – …3000 32 77 317 4 135.50 – …3200 (W140) (W141) bright TiN bright TiN Machine reamer HSS-E DIN 208-B H7 ≈ 7° 1541 TiN 1537 bright Reamers 1.3
RkJQdWJsaXNoZXIy NTg4MTI=