All prices quoted are non-binding recommended prices. 1/72 Design: Particularly sturdy model, nitrided up to Ø 16.0 mm, surface steamtempered from Ø 16.0 mm, with precision ground point and wide flutes with strongly rounded back edges. Application: Suitable for drilling extremely deep holes under difficult conditions e.g. poor chip removal causing deficient cooling of the drill tip. Particularly suitable for grey cast iron and steels up to 850 N/mm2 in strength. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 22 18 – – – – 20 16 – 45 36 – – – – – 1092 Ø h8 x total length mm Spiral length mm Series MT STEEL < 700 N/mm2 f mm/rev 1092 Order No. € 8 x 265 165 1 1 0.125 52.00 …1080 8 x 330 210 2 1 0.125 79.40 …2080 8.5 x 330 210 1 1 0.16 88.70 …2085 9 x 275 175 1 1 0.16 56.70 …1090 9 x 345 220 2 1 0.16 89.50 …2090 10 x 285 185 1 1 0.16 59.90 …1100 10 x 360 235 2 1 0.16 90.40 …2100 10.5 x 285 185 1 1 0.16 72.90 …1105 10.5 x 360 235 2 1 0.16 113.00 …2105 11 x 300 195 1 1 0.16 69.80 …1110 11 x 375 250 2 1 0.16 103.50 …2110 11.5 x 300 195 1 1 0.16 73.40 …1115 11.5 x 375 250 2 1 0.16 110.00 …2115 12 x 310 205 1 1 0.16 74.30 …1120 12 x 395 260 2 1 0.16 125.50 …2120 12.5 x 310 205 1 1 0.16 76.50 …1125 13 x 310 205 1 1 0.2 77.40 …1130 13 x 395 260 2 1 0.2 131.50 …2130 13.5 x 325 220 1 1 0.2 89.30 …1135 13.5 x 410 275 2 1 0.2 140.50 …2135 14 x 325 220 1 1 0.2 86.90 …1140 14 x 410 275 2 1 0.2 140.50 …2140 14.5 x 340 220 1 2 0.2 90.20 …1145 14.5 x 425 275 2 2 0.2 141.50 …2145 15 x 340 220 1 2 0.2 95.00 …1150 15 x 425 275 2 2 0.2 142.00 …2150 15.5 x 355 230 1 2 0.2 103.50 …1155 15.5 x 445 295 2 2 0.2 148.50 …2155 16 x 355 230 1 2 0.2 99.00 …1160 16 x 445 295 2 2 0.2 145.50 …2160 (W100) Ø h8 x total length mm Spiral length mm Series MT STEEL < 700 N/mm2 f mm/rev 1092 Order No. € 16.5 x 355 230 1 2 0.25 99.70 …1165 16.5 x 445 295 2 2 0.25 167.00 …2165 17 x 355 230 1 2 0.25 102.00 …1170 17 x 445 295 2 2 0.25 157.00 …2170 17.5 x 370 245 1 2 0.25 107.00 …1175 17.5 x 465 310 2 2 0.25 169.50 …2175 18 x 370 245 1 2 0.25 111.00 …1180 18 x 465 310 2 2 0.25 176.50 …2180 18.5 x 370 245 1 2 0.25 116.50 …1185 18.5 x 465 310 2 2 0.25 176.50 …2185 19 x 370 245 1 2 0.25 124.50 …1190 19 x 465 310 2 2 0.25 193.00 …2190 19.5 x 385 260 1 2 0.25 135.00 …1195 20 x 385 260 1 2 0.25 143.00 …1200 20 x 490 325 2 2 0.25 217.00 …2200 20.5 x 385 260 1 2 0.315 181.00 …1205 21 x 385 260 1 2 0.315 164.50 …1210 22 x 405 270 1 2 0.315 172.50 …1220 22 x 515 345 2 2 0.315 276.50 …2220 23 x 405 270 1 2 0.315 203.50 …1230 23 x 515 345 2 2 0.315 281.00 …2230 24 x 440 290 1 3 0.315 227.50 …1240 25 x 440 290 1 3 0.315 231.50 …1250 25 x 555 365 2 3 0.315 320.50 …2250 26 x 440 290 1 3 0.315 247.50 …1260 26 x 555 365 2 3 0.315 373.00 …2260 28 x 460 305 1 3 0.315 287.00 …1280 30 x 460 305 1 3 0.315 331.00 …1300 30 x 580 385 2 3 0.315 509.00 …2300 (W100) bright bright Spiral drill, with Morse taper shank, extra long HSS DIN 1870 TF 130° 38° bright Design: Hardness HRC 62 +2, bore rounded at one end, special steel, hardened and ground. Hole F7 mm Diameter n6 mm Length mm 1118 Order No. € 1.9 5 6 3.69 …0190 2 5 6 3.69 …0200 2.1 5 6 3.69 …0210 2.2 5 6 3.69 …0220 2.4 5 6 3.69 …0240 2.5 5 6 3.69 …0250 2.6 5 6 3.69 …0260 2.7 6 8 3.90 …0270 2.8 6 8 3.90 …0280 (W118) Hole F7 mm Diameter n6 mm Length mm 1118 Order No. € 3 6 8 3.90 …0300 3.1 6 8 3.90 …0310 3.2 6 8 3.90 …0320 3.3 6 8 3.90 …0330 3.4 7 8 3.99 …0340 3.5 7 8 3.99 …0350 3.6 7 8 3.99 …0360 3.8 7 8 3.99 …0380 4 7 8 3.99 …0400 (W118) Drill bush, short DIN 179 A Continued on next page Drills HSS/HSS-E 1.1
RkJQdWJsaXNoZXIy NTg4MTI=