FORMAT_EN_2023-25_WCT_Light

Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/55 Set contents Ø h8 mm Number of drills piece Increasing mm 1033 1026 Order No. € € 1–10 19 0.5 174.00 – …0005 1–10.5 24 0.5 + K.B.* 249.50 527.00 …0007 1–13 25 0.5 393.50 867.50 …0009 ​ (W100) (W105) bright bright Spiral drill set, with cylindrical shank * With intermediate sizes for tapped holes: 1 piece each.∅ 3.3; 4.2; 6.8; 10.2 mm. 1026 bright 1033 bright Design: Particularly sturdy drill with excellent thermal resistance. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] – – – 15 12 – – – 8 – – – – – – – 1079 36 – – 22 18 14 – – 12 – – – – – – – 1020 ∅ h8 mm Spiral length mm Total length mm INOX ferrite/ martens. f mm/rev PU 1079 1020 Order No. € € 1 12 34 0.02 10 5.75 7.00 …0100 1.1 14 36 0.02 10 5.70 – …0110 1.2 16 38 0.02 10 5.70 – …0120 1.3 16 38 0.02 10 5.60 – …0130 1.4 18 40 0.02 10 5.60 – …0140 1.5 18 40 0.02 10 5.40 6.55 …0150 1.6 20 43 0.02 10 5.30 – …0160 1.7 20 43 0.02 10 5.30 – …0170 1.8 22 46 0.02 10 5.10 – …0180 1.9 22 46 0.02 10 5.20 – …0190 2 24 49 0.02 10 4.85 5.90 …0200 2.1 24 49 0.02 10 5.35 – …0210 2.2 27 53 0.02 10 5.50 – …0220 2.3 27 53 0.02 10 5.20 – …0230 2.4 30 57 0.02 10 5.65 – …0240 2.5 30 57 0.02 10 5.25 6.40 …0250 2.6 30 57 0.02 10 5.60 – …0260 2.7 33 61 0.02 10 5.85 – …0270 2.8 33 61 0.02 10 5.85 – …0280 ​ (W128) (W100) ∅ h8 mm Spiral length mm Total length mm INOX ferrite/ martens. f mm/rev PU 1079 1020 Order No. € € 2.9 33 61 0.02 10 5.90 – …0290 3 33 61 0.02 10 5.35 6.40 …0300 3.1 36 65 0.02 10 6.35 7.30 …0310 3.2 36 65 0.02 10 5.85 7.00 …0320 3.3 36 65 0.02 10 6.40 7.00 …0330 3.4 39 70 0.02 10 6.35 – …0340 3.5 39 70 0.02 10 6.10 7.00 …0350 3.6 39 70 0.02 10 7.10 – …0360 3.7 39 70 0.02 10 7.15 – …0370 3.8 43 75 0.02 10 7.35 – …0380 3.9 43 75 0.02 10 7.45 – …0390 4 43 75 0.02 10 6.95 7.15 …0400 4.1 43 75 0.03 10 7.45 7.95 …0410 4.2 43 75 0.03 10 7.30 7.95 …0420 4.3 47 80 0.03 10 7.95 – …0430 4.4 47 80 0.03 10 8.05 – …0440 4.5 47 80 0.03 10 7.70 7.95 …0450 4.6 47 80 0.03 10 8.40 – …0460 4.7 47 80 0.03 10 8.35 – …0470 ​ (W128) (W100) TiAlN TiAlN TiAlN TiAlN High-performance spiral drill, with cylindrical shank * VE = 5 pieces Continued on next page DIN 338 INOX 30° 1079 TiAlN Note: Available as a set (Order No. 1079 on Ç 1/56). 1020 TiAlN High-performance jobber drills for particularly strong and high-strength alloys based on CrNi, Hastelloy®, Inconel®, Monel®, Nimonic®, stainless, acid and heat resistant steels, wear-resistant plates and steels, bronzes up to 1400 N/mm2 strength. The special cross-cut geometry enables a very good tapping behaviour, an improved and clean bore accuracy, as well as an excellent bore exit. Made of HSS Co8 for extremely high thermal resistance. Point thinning with cross point according to NAS 907 P3 aviation industry. 1020 TiAlN HSS Co8 135° 1079 TiAlN HSS Co5 130° Drills HSS/HSS-E 1.1

RkJQdWJsaXNoZXIy NTg4MTI=