FORMAT_EN_2023-25_WCT_Light

Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 3/185 Design: Push-pull clamping devices, short design version. Long push rod guide with mounting thread and nut. Galvanised and passivated. Stainless steel rivets. Tempered fitting screws. Bearing bushings greased. Ergonomic, oil-resistant handle with large hand rest and soft component. Application: Can be used as push-pull clamping device. For mounting onto sheet metal walls. In addition, the push-pull toggle clamp can be screwed in into jig bodies with a front-facing thread. Moreover, flange mounting is possible using an angular foot. Scope of delivery: Complete with tempered, galvanised pressure screw. Push-pull toggle clamp Size F1 kN F2 kN Pressing spindle Weight g 3954 Order No. € 2 1 1 M6 x 25 130 29.70 …0020 3 2.5 2.5 M8 x 35 320 34.20 …0030 5 4 4 M12 x 50 1200 55.80 …0050 ​ (W341) Also available in stainless steel design. Dimension table ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ Size A B E H H1 Stroke HW min. HW max. L1 L2 L3 M M2 N 2 10 36 15 24 73 21.5 17 27 68.513 68 M6 M16 x 1.5 30.5 3 12 57 25 33 120.5 40 22 37.5 108 16 115 M8 M20 x 1.5 33 5 16 92 45 37 149 67 30 50 175 24 139 M12 M24 x 1.5 49 Design: Short design version, push-pull clamping devices (push rod and hand lever running parallel). Long push rod guide with mounting thread and nut. Galvanised and passivated. Rustproof rivets for size 2 and 3 that run in case-hardened bearing bushings. Lever components and push rods mode of tempered steel. Bearing bushings greased. Push-pull toggle clamp with front-facing thread for direct installation in sheet metal walls or in jigs. Handle made of red, oil-resistant plastic. For size 0, 2 and 3: Ergonomic, oil-resistant handle with large hand rest and soft component. Complete with tempered, galvanised pressure screw. Application: The ESD push-pull toggle clamp was specially developed for use in ESD protection zones (EPA -electrostatic protected area) for work on electrostatically sensitive components, assemblies or devices in accordance with the DIN EN 61340-5-1 standard. Note: The ESD push-pull toggle clamp is not insulating. It must not be used in areas where open voltages are used. ESD push-pull toggle clamp Size F1 kN F2 kN Pressing spindle Weight g 3824 Order No. € 2 1 1 M6 x 25 130 39.60 …0001 3 2.5 2.5 M8 x 35 320 43.90 …0003 ​ (W341) Dimension table ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ ​ Size A B E H H1 Stroke HW min. HW max. L1 L2 L3 M M2 N 2 10361524 7321.5 17 25 68.513 68M6 M16 x 1.5 30.5 3 12 57 25 33 123 40 22 35 108 16 115 M8 M20 x 1.5 33 Clamping elements 3.8

RkJQdWJsaXNoZXIy NTg4MTI=