Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 3/141 Design: The paste, which is based on mineral grease, has a synergistically acting combination of highly effective, white solid lubricants. It is heat-resistant and water washout resistant (water washout test to DIN 51807, T.2; loss of grease after 1 hr./37.8 °C = 1.4 %). Application: For lubricating frequently used screws/nuts in gripping fixtures. This is particularly so when aggressive cooling lubricants are being used. Non-lubricated (dry) screw connection are subjected to high friction forces (reduction of tension force) and rapid wear when frequently tightened. AMF bolt paste enhances the achievable tension force through optimal sliding characteristics and is gentle on material (longer service life). Operative temperature range °C Content ml 3914 Order No. € -25 to +125 75 8.95 …0075 (W342) Bolt paste Application: For screwing-in and clamping onto jigs. Thread ∅ D mm Length of thread L mm A/F mm Washer height H mm Eccentric travel S1 mm Distance A mm Clamping force kN PU 3917 Order No. € M4 10 8 2.8 0.8 3.8 0.9 10 6.20 …0000 M6 12 16 4.8 1.3 7.8 3.4 10 6.20 …0010 M8 16 20 4.8 1 10.2 3.6 12 6.75 …0020 M10 20 20 6.4 1.6 10.2 9 10 8.10 …0030 M12 25 25 9.5 2 12.7 18 8 10.30 …0040 M16 30 30 12.7 2.5 15 27 4 16.70 …0050 (W343) Eccentric tension clamp Application: The tempered T-nuts are pushed in the T-slot guide and locked with a threaded pin. Tensioning takes place by twisting the eccentric bolt. T-slot width N mm Thread D Recessed hexagon mm A/F mm Washer height H mm Eccentric travel S1 mm Clamping force kN PU 3917 Order No. € 8 M6 3 16 4.8 1 3.4 2 30.50 …0060 10 M6 4 16 4.8 1 3.4 2 31.60 …0070 12 M8 5 21 4.8 1 3.6 2 32.40 …0080 14 M10 7 21 6.4 1.6 9 2 32.80 …0090 16 M12 8 25 9.5 2 18 2 33.50 …0100 18 M12 8 25 9.5 2 18 2 35.00 …0110 20 M16 12 30 12.7 2.5 27 2 43.30 …0120 22 M16 12 30 12.7 2.5 27 2 61.50 …0130 (W343) Eccentric tension clamp, with T-nut Universal clamping system for clamping from all workpiece shapes, whether square, diagonal, concave or convex. Design: The special feature of this clamping device is the steel bolt (strength 10.9) with the eccentric head. The eccentric tappet gives the clamping motion a very high clamping force. A hexagonal brass disc serves as clamping piece. Application: All workpieces with the most varied shapes can be clamped with retaining studs and 1 or 2 clamping screws. The small installation height enables machining the workpiece surface without problems. Thus, the position of the clamping claws does not have to be considered in CNC programming work. In addition, the compact dimensions allow space-saving multiple clamping. The tension clamps can also be used as a stop. Clamping elements 3.8
RkJQdWJsaXNoZXIy NTg4MTI=