All prices quoted are non-binding recommended prices. 3/80 Design: Lightweight construction. Application: For turning unhardened jaws and for grinding hardened base and top jaws. Jaws reversible and infinitely adjustable. The fixture is tensioned in a three-jaw chuck. The adjustment ring on the hollow-out fixture allows the jaws to be moved inwards and outwards as required. The jaws are placed in the bores of the top jaws on the lathe chuck and the chuck is tensioned. The chuck can be set in the position that it will assume when processing workpieces in just a few seconds (pre-tensioning). The cranked clamping surfaces of the chuck jaws are then tensioned form-fit and perfectly concentric. for chuck size mm Outer ∅ mm Inner ∅ mm Nesting area Ø J mm Nesting area Ø A mm Thread B mm 3120 Order No. € 125 153 110 50–115 150–215 M5 20 C◊ …0001 200 176 110 35–125 170–260 M8 31 C◊ …0003 250 215 135 70–140 215–285 M8 31 C◊ …0005 250 244 162 100–175 240–315 M8 31 C◊ …0007 315 290 208 145–215 290–360 M8 31 C◊ …0009 400 342 260 160–270 330–440 M10 31 C◊ …0011 (W301) Jaw hollow-out fixture, for three-jaw chuck Design: Steel flange, finished on machine side, faced on chuck side. Scope of delivery: Flange with set screws, stud bolts or Camlock bolts. Ø A mm/taper Height B mm Taper ∅ C mm Taper Ø D mm Drill hole ∅E mm Set screws/stud bolts/ Camlock bolts 3080 3082 Order No. € € 3080 3082 3080 3082 125/ 4 19 27 102 112 63.513 40 3/3/3 212.00 C◊ …0005 160/ 4 21 28 112 117.5 63.513 40 3/3/3 212.00 C◊ …0008 160/ 5 21 31 135 146 82.563 40 4/4/6 212.00 C◊ …0011 200/ 5 21 31 135 146 82.563 50 4/4/6 262.50 C◊ …0014 200/ 6 23 36 170 181 106.375 50 4/4/6 262.50 C◊ …0017 250/ 6 23 36 170 181 106.375 63 4/4/6 327.50 C◊ …0020 250/ 8 26 39 220 225.4 139.719 63 4/4/6 327.50 C◊ …0023 315/ 6 26 39 220 225.4 139.719 63 4/4/6 412.50 C◊ …0026 315/ 8 26 39 220 225.4 139.719 63 4/4/6 C◊ C◊ …0029 315/ 11 33 45 290 298.4 196.869 63 6/6/6 412.50 C◊ …0032 400/ 8 31 39 220 225.4 139.719 63 4/4/6 C C◊ B …0035 400/ 11 31 45 290 298.4 196.869 63 6/6/6 699.50 C◊ B …0038 (W301) (W301) Short taper flange 3080 DIN 55027 and DIN 55022, with stud bolt and collar nut. 3082 DIN 55029 and ASA B 5.9 D 1, with stud bolt for camlock. 3082 DIN 55029 3080 DIN 55027 Lathe chucks 3.2
RkJQdWJsaXNoZXIy NTg4MTI=