Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/317 Design: Ultra-fine grit solid carbide, with centre cut. Cutting speed approx. 50% higher than with non-coated tools. Dry machining possible. Air cooling recommended. Application: Can be used for peripheral milling as well as for universal machining. For milling depths up to 2 x D. Can also be used for trimming and finishing milling. Can be used for rough grinding, slot cutting and finishing milling. The irregular from 35°/38° helical pitch results in particularly smooth running and thus very good surface on the workpiece. A much longer tool life is achieved than with conventional tools, as well as maximum stability during machining. In addition, feeds higher by up to 60% can be realised. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 190 152 122 – – 70 200 160 70 – – – – 100 – – 2448 ∅ d1 = h10 mm Cutting length l2 mm Total length l1 mm Shank ∅ d2 = h6 mm STEEL < 1000 N/mm2 fz mm 2448 Order No. € 6 13 57 6 0.039 34.50 …0600 8 19 63 8 0.053 48.60 …0800 10 22 72 10 0.065 73.10 …1000 12 26 83 12 0.079 93.30 …1200 14 26 83 14 0.095 124.50 …1400 16 32 92 16 0.095 162.50 …1600 18 32 92 18 0.11 227.50 …1800 20 38 104 20 0.11 251.50 …2000 (W220) Fire End mill, with 35°/38° helical pitch Solid carbide N 4 DIN 6527 DIN 6535-HA 35°/38° Fire Design: With centre cut, suitable for drilling. Application: Can be used for peripheral milling as well as for universal machining. Can also be used for trimming and finishing milling. Can be used for rough grinding, slot cutting and finishing milling. The irregular helical pitch results in particularly smooth running and thus very good surface on the workpiece. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 190 152 122 – – 70 200 160 70 – – – – 100 – – 2462 ∅ d1 = h10 mm Cutting length l2 mm Total length l1 mm Shank ∅ d2 = h6 mm STEEL < 1000 N/mm2 fz mm 2462 Order No. € 6 13 57 6 0.039 37.30 …0600 8 19 63 8 0.053 51.50 …0800 10 22 72 10 0.065 75.80 …1000 12 26 83 12 0.079 96.00 …1200 14 26 83 14 0.095 130.00 …1400 16 32 92 16 0.095 169.00 …1600 18 32 92 18 0.11 233.00 …1800 20 38 104 20 0.11 257.00 …2000 (W220) Fire End mill, with 35°/38° helical pitch Solid carbide N 4 DIN 6527 DIN 6535-HB 35°/38° Fire Solid carbide milling cutters 1.9
RkJQdWJsaXNoZXIy NTg4MTI=