Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/297 Design: With relief ground cord profile. With centre cut, suitable for drilling. Application: Can be used for peripheral and end milling. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 40 30 20 – – – – – – 105 – – – – – – 2190 – 36 – – – – – – – – – – – – – – 2196 ∅ d1 = js12 mm Cutting length l2 mm Total length l1 mm Shank ∅ d2 = h6 mm Corner chamfer mm Number of teeth STEEL < 1000 N/mm2 f mm 2190 2196 Order No. € € 6 13 57 6 0.25 3 0.013 18.80 22.10 …0600 7 16 66 10 0.25 3 0.013 – 26.50 …0700 8 19 69 10 0.25 3 0.021 19.95 25.90 …0800 9 19 69 10 0.34 3 0.021 – 27.20 …0900 10 22 72 10 0.34 4 0.044 19.95 27.20 …1000 11 22 79 12 0.5 4 0.044 – 29.60 …1100 12 26 83 12 0.5 4 0.058 22.30 30.20 …1200 14 26 83 12 0.55 4 0.067 28.20 37.10 …1400 16 32 92 16 0.55 4 0.083 31.70 40.20 …1600 18 32 92 16 0.55 4 0.093 33.30 44.90 …1800 19 32 92 16 0.55 4 0.096 38.40 – …1900 20 38 104 20 0.55 4 0.106 38.40 57.20 …2000 (W206) (W214) bright TiAlN Roughing end mill HSS Co8 NR 3–4 DIN 844-K DIN 1835-B 30° 45° 2196 TiAlN 2190 bright Design: With relief ground cord profile. With centre cut, suitable for drilling. Application: Can be used for peripheral and end milling. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 40 30 20 – – – – – – 110 – – – – – – 2199 ∅ d1 = js12 mm Cutting length l2 mm Total length l1 mm Shank ∅ d2 = h6 mm Corner chamfer mm Number of teeth STEEL < 1400 N/mm2 fz mm 2199 Order No. € 6 24 68 6 0.25 3 0.013 24.20 …0600 8 38 88 10 0.25 3 0.021 25.70 …0800 10 45 95 10 0.34 4 0.033 26.30 …1000 12 53 110 12 0.5 4 0.044 30.30 …1200 16 63 123 16 0.55 4 0.063 44.50 …1600 18 63 123 16 0.55 4 0.07 50.40 …1800 20 75 141 20 0.55 4 0.08 55.60 …2000 (W206) bright Roughing end mill HSS Co8 NR 3–4 DIN 844-L DIN 1835-B 30° bright End mills HSS-E/HSS-E PM 1.8
RkJQdWJsaXNoZXIy NTg4MTI=