FORMAT_EN_2023-25_WCT_Light

Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 8/5 Design: Shank mounted single- or one-stone abrasive diamond block, solid-shaped crystal with few occlusions or irregular cracking, no crevices. Application: For profiling e.g. abrasives for all ceramic-bonded abrasive discs. The abrasive is always clamped so that the angle to the middle of the abrasive disc is between 5° and 15°. Dressing work with diamonds is better wet and with plenty of ventilation as they are sensitive to shock and temperature. As the diamond becomes progressively blunt it should be twisted 90°. Note: The choice of the right diamond size depends on the Ø of the abrasive disc, e.g. the wheel width. Worn diamond abrasives should be regularly replaced. Diamond size/carat weight approx. Shank For grinding wheel ∅ up to mm 8512 Order No. € 0.25 MK 0 150 39.30 …0025 0.50 MK 0 300 71.10 …0050 0.75 MK 0 400 112.00 …0075 1.00 MK 0 500 162.00 …0100 0.25 MK 1 150 39.30 …1025 0.50 MK 1 300 71.10 …1050 0.75 MK 1 400 112.00 …1075 1.00 MK 1 500 162.00 …1100 1.50 MK 1 750 227.00 …1150 0.25 cyl. ∅ 8 x 80 mm 150 39.30 * …2025 0.50 cyl. ∅ 8 x 80 mm 300 71.10 * …2050 0.75 cyl. ∅ 8 x 80 mm 400 112.00 * …2075 1.00 cyl. ∅ 8 x 80 mm 500 162.00 * …2100 1.50 cyl. ∅ 8 x 80 mm 750 227.00 * …2150 ​ (W859) Diamond single point dressing tool * Other shapes and sizes available upon request. From 1.5 carats with remote head Design: 5 diamonds, in a special sintered binding, so that they can be used right to the end without changing. Application: The diamond multi-point dressing tool is a practical dressing tool for coarse grinding with abrasive discs of all diameters up to 100 grit. Note: To prolong the life of this sharpener, continuous cooling should be used during the dressing process. Diamond size/carat weight approx. 8515 8518 8521 Order No. € € € 1.00 126.00 126.00 126.00 * …0005 ​ (W859) (W859) (W859) Diamond multiple-stone honer * Other shapes and sizes available upon request. 8515 MK 0. Overall length 40 mm. 8518 MK 1. Overall length 57 mm. 8521 Cyl. shank ∅ 8 x 80 mm. 8521 8518 8515 Design: Single-sintered, high-concentrate (2.5 carat) diamond grain. Diamond cylinder set in the shank (so no loss of diamonds), universal type. Application: Because of the multiple working points on an efficient diamond tool sharpener, it is only for straight abrasive disc surfaces (flat and peripheral edge). These abrasives have no gradient, so the whole of the diamond grit is employed. Sharpener is not recovered, it is durable and can be used until worn. Not suitable for detail work. For use with wheel grain 36-120. Note: Adequate cooling before and during the dressing process maximises its life span. Diamond size/carat weight approx. Diamond inset ∅ mm 8524 8527 8530 Order No. € € € 2.50 8 74.80 74.80 74.80 * …0005 ​ (W859) (W859) (W859) Diamond multi-grain dressing tool * Other shapes and sizes available upon request. 8524 MK 0. Overall length 40 mm. 8527 MK 1. Overall length 57 mm. 8530 Cyl. shank ∅ 10 x 80 mm. 8530 8527 8524 Grinding wheel dressers 8

RkJQdWJsaXNoZXIy NTg4MTI=