Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/137 Design: The uneven tooth pitch ensure chatter-free and accurate drilling. With cylinder shank. Application: For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447, DIN 7977 and DIN 7978. Perfectly suited for single and serial production. Pre-drill with a pin drill (Order No. 1052, Ç 1/65). Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] C U V U U – U U V U U U – – – – 1510 Nominal-∅ mm Small/large Ø mm Cutting edge length mm Total length mm Shank ∅ h9 mm 1510 Order No. € 2 1.9/ 2.86 48 86 3.15 29.60 …0200 2.5 2.4/ 3.36 48 86 3.15 35.40 …0250 3 2.9/ 4.06 58 100 4 32.10 …0300 4 3.9/ 5.26 68 112 5 32.50 …0400 5 4.9/ 6.36 73 122 6.3 34.60 …0500 6 5.9/ 8 105 160 8 39.70 …0600 8 7.9/ 10.8 145 207 10 59.00 …0800 10 9.9/ 13.4 175 245 12.5 75.60 …1000 12 11.8/ 16 210 290 16 94.50 …1200 (W140) bright Machine taper reamer HSS-E DIN 2179 ≈ 45° 1:50 bright Design: The uneven tooth pitch ensure chatter-free and accurate drilling. With cylinder shank with square drive. Application: For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447, DIN 7977 and DIN 7978. Perfectly suited for single production or repair work. Also suitable for holes with interrupted cut. Pre-drill with a cylindrical jobber drill or pin drill. Note: Tap wrenches for manual actuation - see page Ç 1/252. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] C U V V V – U U V U U U – – – – 1508 Nominal-∅ mm Small/large Ø mm Cutting edge length mm Total length mm Spanner width mm 1508 Order No. € 3 2.9/ 4.06 58 80 3 23.00 …0300 4 3.9/ 5.26 68 93 3.8 26.20 …0400 5 4.9/ 6.36 73 100 4.9 27.50 …0500 6 5.9/ 8 105 135 6.2 33.20 …0600 8 7.9/ 10.8 145 180 8 51.50 …0800 10 9.9/ 13.4 175 215 10 72.80 …1000 12 11.8/ 16 210 255 11 92.60 …1200 13 12.8/ 17 210 255 12 107.50 …1300 14 13.8/ 18 210 255 12 114.00 …1400 16 15.8/ 20.4 230 280 14.5 128.50 …1600 20 19.8/ 24.8 250 310 18 166.50 …2000 (W140) bright Taper pin hand reamer HSS DIN 9-B ≈ 7° 1:50 bright Reamers 1.3
RkJQdWJsaXNoZXIy NTg4MTI=