Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/131 Design: Quadruple-edged, special grinding and special thinning. Application: For drilling and reaming into the full piece in one step, with a possible achievable drill hole tolerance of IT7. This significantly reduces the main and additional times, with the same surface quality, dimensional accuracy and roundness as with reaming. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 65 45 30 – – – 60 50 – – – – – – – – 1232 Nominal-∅ mm Spiral length mm Total length mm Shank ∅ = h6 mm STEEL < 700 N/mm2 f mm/rev 1232 Order No. € 5.98 44 81 6 0.18 123.00 …0598 5.99 44 81 6 0.18 123.00 …0599 6 44 81 6 0.18 123.00 …0600 6.01 44 81 6 0.18 123.00 …0601 6.02 53 91 6 0.18 123.00 …0602 7.98 53 91 8 0.2 123.00 …0798 7.99 53 91 8 0.2 123.00 …0799 8 53 91 8 0.2 123.00 …0800 8.01 53 91 8 0.2 123.00 …0801 8.02 53 91 8 0.2 123.00 …0802 9.98 61 103 10 0.25 174.50 …0998 9.99 61 103 10 0.25 174.50 …0999 (W111) Nominal-∅ mm Spiral length mm Total length mm Shank ∅ = h6 mm STEEL < 700 N/mm2 f mm/rev 1232 Order No. € 10 61 103 10 0.25 174.50 …1000 10.01 61 103 10 0.25 174.50 …1001 10.02 61 103 10 0.25 174.50 …1002 11.98 71 118 12 0.25 251.00 …1198 11.99 71 118 12 0.25 251.00 …1199 12 71 118 12 0.25 251.00 …1200 12.01 71 118 12 0.35 251.00 …1201 12.02 71 118 12 0.35 251.00 …1202 14 77 124 14 0.35 341.50 …1400 16 83 133 16 0.35 423.00 …1600 18 93 143 18 0.4 589.00 …1800 20 101 153 20 0.4 714.50 …2000 (W111) TiAlN TiAlN Drill reamer, 5 x D, T4 Solid carbide N 4 DIN 6535-HA 140° 5xD TiAlN Design: Specific ground point with pyramid. 4 guide chamfers. Drill tolerance: ≥ IT7. Application: With pyramid tip, angled bore entry up to maximum 10°. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] C C C – – – C C – – – – – – – – 1241 Drill reamer pyramid, 5 x D m TiAlN Solid carbide 2 DIN 6535-HA 140° 30° 5xD Nominal-∅ mm Fit tolerance mm Spiral length mm Total length mm Shank ∅ = h6 mm 1241 Order No. € 4 H7 36 74 6 144.50 …0400 5 H7 53 91 6 144.50 …0500 5.98 ±0.003 53 91 6 144.50 …0598 6 ±0.003 53 91 6 144.50 …0600 6 H7 53 91 6 144.50 …0607 6.01 ±0.003 53 91 6 144.50 …0601 6.02 ±0.003 53 91 6 144.50 …0602 7 H7 53 91 8 162.50 …0700 7.98 ±0.003 53 91 8 162.50 …0798 8 ±0.003 53 91 8 162.50 …0800 8 H7 53 91 8 162.50 …0807 8.01 ±0.003 53 91 8 162.50 …0801 8.02 ±0.003 53 91 8 162.50 …0802 9 H7 61 103 10 162.50 …0900 (W141) Nominal-∅ mm Fit tolerance mm Spiral length mm Total length mm Shank ∅ = h6 mm 1241 Order No. € 9.54 ±0.003 61 103 10 235.50 …0954 10 ±0.003 61 103 10 235.50 …1000 10 H7 61 103 10 235.50 …1007 10.01 ±0.003 61 103 10 235.50 …1001 10.02 ±0.003 61 103 10 235.50 …1002 11.98 ±0.003 71 118 12 293.50 …1198 11.99 ±0.003 71 118 12 293.50 …1199 12 ±0.003 71 118 12 293.50 …1200 12 H7 71 118 12 293.50 …1207 12.01 ±0.003 71 118 12 293.50 …1201 12.02 ±0.003 71 118 12 293.50 …1202 12.7 ±0.003 77 124 14 396.50 …1270 14 H7 77 124 14 396.50 …1400 16 H7 83 133 16 494.00 …1600 (W141) TiAlN TiAlN Solid carbide drills 1.2
RkJQdWJsaXNoZXIy NTg4MTI=