Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/129 m Design: The 6 guide chamfers ensure very high alignment accuracy and stabilisation of the drill, even at very high cutting speeds and feeding rates. Application: Solid carbide high-performance drill with inner cooling channels, especially for aluminium machining. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] – – – – – – – – – 360 180 170 – – – – 1171 High-performance drill, alu m Solid carbide DIN 6537 W DIN 6535-HA DUO+ Design: Triple-edged with point-shaped tip, special grinding and special thinning. Angle of rake 28°, core thickness thicker than normal and without core gradient. Application: For drilling into the solid for positionally and form-accurate holes up to 5 x D. Note: Initial centring may be unnecessary due to the centring point. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] – – – – – – 80 70 – 150 120 180 – – – – 1233 ∅ = m7 mm Spiral length mm Shank length l3 mm Total length mm Shank ∅ = h6 mm CAST GG/GTS f mm/rev 1233 Order No. € 3 28 36 66 6 0.1 C◊ …0300 3.1 28 36 66 6 0.1 C◊ …0310 3.2 28 36 66 6 0.125 C◊ …0320 3.3 28 36 66 6 0.125 C◊ …0330 3.5 28 36 66 6 0.125 C◊ …0350 (W112) bright Spiral drill, SuperLine, 5 x D Continued on next page Solid carbide DIN 6537 FT200 3 DIN 6535-HA 130° 28° 5xD bright ∅ h7 mm Spiral length mm Total length mm Shank ∅ = h6 mm ALU < 8% Si f mm/rev 1171 Order No. € 2.8 21 57 4 0.125 99.20 …0280 3 28 66 6 0.125 99.20 …0300 3.3 28 66 6 0.125 99.20 …0330 3.5 28 66 6 0.125 99.20 …0350 3.7 28 66 6 0.125 99.20 …0370 4 36 74 6 0.14 99.20 …0400 4.2 36 74 6 0.14 99.20 …0420 4.5 36 74 6 0.14 99.20 …0450 5 44 82 6 0.15 99.20 …0500 5.5 44 82 6 0.15 99.20 …0550 6 44 82 6 0.18 99.20 …0600 6.5 53 91 8 0.18 114.00 …0650 6.8 53 91 8 0.18 114.00 …0680 7 53 91 8 0.19 114.00 …0700 7.5 53 91 8 0.19 114.00 …0750 7.8 53 91 8 0.19 114.00 …0780 8 53 91 8 0.2 114.00 …0800 8.5 61 103 10 0.2 133.00 …0850 9 61 103 10 0.235 133.00 …0900 9.5 61 103 10 0.235 133.00 …0950 (W110) ∅ h7 mm Spiral length mm Total length mm Shank ∅ = h6 mm ALU < 8% Si f mm/rev 1171 Order No. € 10 61 103 10 0.24 133.00 …1000 10.2 71 118 12 0.24 187.50 …1020 10.5 71 118 12 0.24 187.50 …1050 11 71 118 12 0.245 187.50 …1100 11.2 71 118 12 0.245 187.50 …1120 11.5 71 118 12 0.245 187.50 …1150 12 71 118 12 0.25 187.50 …1200 12.5 77 124 14 0.25 246.00 …1250 13 77 124 14 0.285 246.00 …1300 13.1 77 124 14 0.285 246.00 …1310 13.5 77 124 14 0.285 246.00 …1350 14 77 124 14 0.29 246.00 …1400 14.5 83 133 16 0.29 298.50 …1450 15 83 133 16 0.295 298.50 …1500 15.1 83 133 16 0.295 298.50 …1510 15.5 83 133 16 0.295 298.50 …1550 16 83 133 16 0.3 298.50 …1600 (W110) DUO+ DUO+ Solid carbide drills 1.2
RkJQdWJsaXNoZXIy NTg4MTI=