All prices quoted are non-binding recommended prices. 7/32 Design: DIN 7200-A, made of special tool steel, drop-forged, with finely polished tip and powder-coated shank. Hardened and annealed cutting edge, slightly conical interior for simple removal of cut-out. Application: For punching leather, felt, foam, etc. Hole ∅ mm 7120 Order No. € 2 4.27 …0002 3 4.27 …0003 4 4.27 …0004 5 4.27 …0005 6 4.27 …0006 7 4.39 …0007 8 4.39 …0008 9 4.54 …0009 10 5.10 …0010 11 5.65 …0011 12 6.00 …0012 13 7.10 …0013 14 7.35 …0014 15 7.95 …0015 16 8.85 …0016 (W572) Hole ∅ mm 7120 Order No. € 17 9.20 …0017 18 9.85 …0018 19 10.30 …0019 20 11.50 …0020 22 13.10 …0022 24 15.70 …0024 25 16.45 …0025 26 17.65 …0026 28 18.25 …0028 30 20.40 …0030 32 24.90 …0032 35 26.30 …0035 40 36.70 …0040 (W572) Wad punches Design: Supplied in roll-up case. Design Set content 7121 Order No. € 19-pc 2; 3; 4; 5; 6; 7; 8; 9; 10; 11; 12; 13; 14; 15; 16; 17; 18; 19; 20 mm 121.50 …0010 15-pc 2; 4; 6; 8; 10; 12; 14; 16; 18; 20; 22; 24; 26; 28; 30 mm 147.00 …0020 (W572) Wad punch set Design: Made of high-strength special steel, ground and finely polished hole punch inserts. For cutting soft materials (rubber, leather, felt, foam). Reinforced materials (metal sheet, glass fibre) up to 0.3 can also be punched. Supplied in plastic case. Design Set content 7126 Order No. € 11-pc Punches from 3 to 20 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20 mm Holder 88.00 …0020 16-pc Punches from 3 to 30 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20; 22; 24; 26; 28; 30 mm Holder 135.00 …0030 21-pc Punches from 3 to 40 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20; 22; 24; 26; 28; 30, 32; 34; 36; 38; 40 mm Block holder 219.00 …0040 26-pc Punches from 3 to 50 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20; 22; 24; 26; 28; 30, 32; 34; 36; 38; 40; 42; 44; 46; 48; 50 mm Block holder 289.50 …0050 33-pc Punches from 3 to 60 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20; 22; 24; 26; 28; 30; 32; 34; 36; 38; 40, 42; 44; 46; 48; 50; 52; 54; 56; 58; 60 mm Block holders 11 to 60 mm Holders 3 to 30 mm Circle cutter 500 mm 362.50 …0060 (W518) Hole punch set 7126 0020 7126 0030 7126 0050 7126 0040 7126 0060 Hole punches 7
RkJQdWJsaXNoZXIy NTg4MTI=