FORMAT_EN_2023-25_WCT_Light

Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 6/283 ​ Design: DIN 7261, Form A, rectangular and hewn on 3 sides. Application: Suitable for processing rectangular geometries and deburring. Can also be used for surface machining. Length mm Cut Cross-section mm 6530 6533 Order No. € € 100 1 12 x 2.5 3.12 – …0101 100 2 12 x 2.5 3.31 – …0102 100 3 12 x 2.5 3.41 – …0103 150 1 16 x 4 3.45 6.80 …0151 150 2 16 x 4 3.53 6.85 …0152 150 3 16 x 4 3.74 7.20 …0153 200 1 20 x 5 4.10 8.35 …0201 200 2 20 x 5 4.32 8.70 …0202 200 3 20 x 5 4.57 8.95 …0203 ​ (W548) (W551) Length mm Cut Cross-section mm 6530 6533 Order No. € € 250 1 25 x 6 5.55 10.40 …0251 250 2 25 x 6 5.75 10.75 …0252 250 3 25 x 6 6.40 11.55 …0253 300 1 30 x 6.5 7.40 – …0301 300 2 30 x 6.5 7.90 – …0302 300 3 30 x 6.5 8.40 – …0303 350 1 35 x 7.5 10.25 – …0351 350 2 35 x 7.5 10.65 – …0352 350 3 35 x 7.5 11.20 – …0353 ​ (W548) (W551) Flat blunt file 6530 With tang. 6533 With ergonomic shaped 2-component plastic handle, roll-off protection and hanging hole. 6533 6530 Design: DIN 7261, Form B, rectangular, tapering point and hewn on 4 sides. With ergonomic shaped 2-component plastic handle, roll-off protection and hanging hole. Application: Suitable for processing rectangular geometries, deburring as well as filing perforations. Can also be used for surface machining. Length mm Cut Cross-section mm 6535 Order No. € 200 1 20 x 5 8.55 …0201 200 2 20 x 5 8.70 …0202 200 3 20 x 5 9.05 …0205 ​ (W551) Length mm Cut Cross-section mm 6535 Order No. € 250 1 25 x 6 10.10 …0251 250 2 25 x 6 10.30 …0252 250 3 25 x 6 10.90 …0253 ​ (W551) Flat pointed file Design: DIN 7261, Form C, triangular, tapering point and hewn on 3 sides. Application: Suitable for deburring as well as filing perforations. Can also be used for surface machining. Length mm Cut Cross-section mm 6542 6545 Order No. € € 100 1 8 3.80 – …0101 100 2 8 4.10 – …0102 100 3 8 4.45 – …0103 150 1 11 4.51 8.25 …0151 150 2 11 4.63 8.50 …0152 150 3 11 4.75 8.70 …0153 200 1 15 5.40 10.15 …0201 200 2 15 5.60 10.40 …0202 ​ (W548) (W551) Length mm Cut Cross-section mm 6542 6545 Order No. € € 200 3 15 5.85 10.85 …0203 250 1 17.5 7.65 – …0251 250 2 17.5 8.05 – …0252 250 3 17.5 8.85 – …0253 300 1 20 11.15 – …0301 300 2 20 11.55 – …0302 300 3 20 11.90 – …0303 ​ (W548) (W551) Three edge file 6542 With tang. 6545 With ergonomic shaped 2-component plastic handle, roll-off protection and hanging hole. 6545 6542 General information: An appropriate steel microstructure, essential for uniform hardness. Type and angle of the cut are determined by the particular application, whereby a differentiation is made between cut 1 – for rough machining, cut 2 – half smooth/universal andcut 3 – finishing. Ideal tooth geometry for each application. The length of the file is measured without the tang from the tip to the attachment. ​ Workshop files 6

RkJQdWJsaXNoZXIy NTg4MTI=