FORMAT_EN_2023-25_WCT_Light

Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/95 Design: Very sturdy model with precision ground point and narrow cross blade. With a side clearance angle of 12°/30°. From ∅ 6 mm with carrier surface according to DIN 6535-HB. ∅-Tolerance up to ∅ 10 mm = h6, From ∅ 10 mm = h8. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 65 52 42 30 24 19 90 72 40 100 100 – – – – – 1172 65 52 42 30 24 19 90 72 35 200 200 – – – – – 1176 ∅ h6 mm Slot length mm Total length mm STEEL < 700 N/mm2 f mm/rev 1172 1176 Order No. € € 2 8 38 0.03 23.40 23.40 …0200 3 12 46 0.05 23.40 23.40 …0300 4 12 55 0.06 25.40 25.40 …0400 5 14 62 0.07 29.00 27.30 …0500 6 16 66 0.09 32.10 29.90 …0600 ​ (W108) (W108) ∅ h6 mm Slot length mm Total length mm STEEL < 700 N/mm2 f mm/rev 1172 1176 Order No. € € 8 21 79 0.1 52.30 44.70 …0800 10 25 89 0.13 71.90 53.30 …1000 12 30 102 0.16 94.30 64.00 …1200 16 37 115 0.2 129.00 141.50 …1600 20 45 131 0.23 240.50 230.50 …2000 ​ (W108) (W108) TiAlN TiAlN TiAlN TiAlN NC spotting drill, with cylinder shank Solid carbide N DIN 6535-HB 90° 142° 1172/ 1176 1172 TiAlN 90° – For drilling and simultaneous countersinking if a spiral drill with a smaller Ø is to follow. 1176 TiAlN 142° – Particularly gentle on the cutting edges of the following solid carbide spiral drill, which results in a significantly longer tool life. Design: With precise tip grinding, steam-treated grooves and carbide-tipped inserts to DIN 8010. Delivery from ∅ 3 mm: Shank with driver acc. to DIN 1809 for use in clamping sleeves. Application: Particularly suitable for steels up to 60 HRC, chilled cast iron over 300 HB, pure molybdenum and tough bronzes. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 80 64 51 – – – 80 70 – – – 180 – 20 10 – 1191 ∅ h8 mm Spiral length mm Total length mm CAST GG/GTS f mm/rev 1191 Order No. € 2 18 45 0.063 12.80 …0200 2.2 18 45 0.063 15.15 …0220 2.5 18 45 0.063 12.80 …0250 2.8 20 50 0.063 15.15 …0280 3 20 50 0.063 12.55 …0300 3.1 25 56 0.063 14.65 …0310 3.2 25 56 0.08 14.65 …0320 3.3 25 56 0.08 14.65 …0330 3.4 25 56 0.08 14.65 …0340 3.5 25 56 0.08 11.20 …0350 3.6 25 56 0.08 12.85 …0360 3.7 25 56 0.08 12.85 …0370 3.8 25 56 0.08 12.85 …0380 4 25 56 0.08 11.20 …0400 4.1 28 63 0.08 12.95 …0410 4.2 28 63 0.08 12.95 …0420 4.3 28 63 0.08 12.95 …0430 4.5 28 63 0.08 11.65 …0450 4.8 28 63 0.08 12.95 …0480 5 28 63 0.08 11.40 …0500 5.1 32 71 0.1 12.95 …0510 5.2 32 71 0.1 14.25 …0520 5.4 32 71 0.1 14.25 …0540 ​ (W110) ∅ h8 mm Spiral length mm Total length mm CAST GG/GTS f mm/rev 1191 Order No. € 5.5 32 71 0.1 12.10 …0550 5.8 32 71 0.1 14.25 …0580 6 32 71 0.1 12.10 …0600 6.5 32 71 0.125 12.85 …0650 6.8 40 80 0.125 12.95 …0680 7 40 80 0.125 13.70 …0700 7.5 40 80 0.125 14.25 …0750 8 40 80 0.125 14.25 …0800 8.5 50 90 0.16 17.40 …0850 9 50 90 0.16 15.40 …0900 9.5 50 90 0.16 18.60 …0950 10 56 100 0.16 19.50 …1000 10.2 56 100 0.16 29.80 …1020 10.5 56 100 0.16 22.10 …1050 11 56 100 0.16 19.50 …1100 11.5 63 112 0.16 26.10 …1150 12 63 112 0.16 22.60 …1200 12.5 63 112 0.16 29.80 …1250 13 63 112 0.2 28.00 …1300 13.5 71 125 0.2 36.80 …1350 14 71 125 0.2 35.90 …1400 15 71 125 0.2 41.40 …1500 16 80 140 0.2 47.50 …1600 ​ (W110) bright bright Solid carbide factory standard spiral drill, with cylindrical shank Carbide DIN 8037 N 118° bright _ Solid carbide drills 1.2

RkJQdWJsaXNoZXIy NTg4MTI=