Additional freight charges may apply for articles over 110 cm. Articles marked with ◊ are not stock items, they are procured at short notice. 1/85 Design: Easy centring, tapping and precisely round drilling is guaranteed by the special point geometry with 90° centre tip. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 40 30 – 25 25 25 – – – 40 40 – – – – – 1011 40 30 – 25 25 25 40 40 – 40 40 – – – – – 1011 ∅ mm Total length mm 1011 Order No. € 6 66 7.45 …0602 8 79 9.50 …0802 (W017) ∅ mm Total length mm 1011 Order No. w € 6 66 8.80 …0060 8 79 11.50 …0080 (W017) bright Welded point drill, with cylindrical shank HSS Co5 25–30° 1011 0060 + 0080 TiCN Note: Particularly suitable for lubricating materials such as aluminium and INOX. 1011 0060–1011 0080 TiCN 1011 0602–1011 0802 bright Design: Cutting depth up to 30 mm, with Weldon shank Ø 19 mm, CBNground. Application: For use in magnetic base drills and column drills with MT mount. The core drill only machines a thin material ring. The remaining drill core is ejected by a guide and ejector pin using spring force. The chips are quickly moved up for disposal and the risk of breakage is minimised. Even large drilling diameters require relatively low amounts of energy. The core drill machines only a small part of the overall area in comparison to the jobber drill. This results in huge savings in power and time. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 30 20 – 15 15 15 – – – 30 30 – – – – – 1337 30 20 – 15 15 15 – – – 30 30 – – – – – 1338 30 20 – 15 15 15 – – – 30 30 – – – – – 1339 Drill bit -∅ mm 1337 1338 1339 Order No. € € € 12 21.70 18.30 23.60 …1230 13 21.90 18.30 23.90 …1330 14 20.50 20.80 22.40 …1430 15 23.50 20.80 25.60 …1530 16 24.70 23.20 26.90 …1630 17 25.80 23.20 28.20 …1730 (W123) (W123) (W123) Drill bit -∅ mm 1337 1338 1339 Order No. € € € 18 27.20 24.90 29.70 …1830 19 28.30 24.90 31.00 …1930 20 30.30 27.60 33.20 …2030 21 31.00 27.60 33.90 …2130 22 29.90 31.00 32.60 …2230 23 32.50 31.00 35.40 …2330 (W123) (W123) (W123) bright TiAlN TiAlN bright TiAlN TiAlN Core drill 1339 TiAlN HSS Co 1338 TiAlN HSS 1337 bright HSS Co Design: With double-sided cutting, replaceable and rotating milling bit as well as setting screw for precisely setting the milling depth. The hexagonal shank causes a 100% power transfer, thus in every bushing the countersink is extremely slip-free. Application: For detaching spot welded sheet parts without misshaping the sheet or pulling it out. Scope of delivery: Spot weld milling cutter with milling bit and centring pin. Use STEEL INOX CAST SPEC. ALLOY NON-FERROUS METAILS HARDENED STEEL Order No. < 700 N/mm2 < 1000 N/mm2 < 1400 N/mm2 ferrite/ martens. Austenitic Duplex GG/ GTS GGG Titanium > 850 N/mm2 Alu < 8% Si Alu > 8% Si Copper/ copper-alloy Graphite GFK/CFK/ Duropl. < 55 HRC < 60 HRC > 60 HRC VC [m/min] 15 – – – – – – – – 30 30 – – – – – 1011 Design Milling cutter Ø mm Total length mm Hexagonal mm 1011 Order No. € Compl. spot weld milling cutter 10 72 7 16.35 …0102 Spare milling bit 10 – – 7.25 …0010 Spare centring pin – – – 1.06 …0001 (W017) Spot weld milling cutter, hexagonal shank HSS Continued on next page Drills HSS/HSS-E 1.1
RkJQdWJsaXNoZXIy NTg4MTI=